Search results

It was the fuel Pump. Did this all from under the truck. The tools to use are a standard sized 3/8 ratchet with a deep barrel 11 mm socket for the pump bolts and a 1/4 inch ratchet with a metric socket to get the plate off to get to the push rod. I did put the push rod in the freezer and used a...

There is no fuel from the fuel pump to the filter. Fuel pump must be bad. I am trying to get the back bolt off now with no luck. there is so little room. Thanks.

Thanks gentleman.

Thanks CUCVLover. Yes stock fuel filter. I don't know how to do the above checks but I guess I will have to learn how. Plan on putting on a screw on filter just have been fixing other things that needed to be fixed. Have the WIX parts and connectors have to make a bracket and get some new fuel line.

This truck is driving me Crazy. As soon as I fix one thing it's something else. It has always started well. I did a 12 volt conversion and had some electrical problems that I fixed with help here. The new starter turns it over better than the old one. It was a little hard starting in that it...

You gentleman are the best. I will try to digest this new information. I wired the light and gage exactly as I found them wired to the old gage and old gage light. The wires I wiggled where the ones to the light up in the dash. I didn't mess with the relay wires. All I did was check voltage at...

Here are some pictures of the wiring:

Warthog your help is greatly appreciated. Checked the connector for the relay and I do have power to a pink/blk stripe wire with the ignition switch on. There is a black/white stripe wire and 3 other black wires going into the connector. 2 of the black wires come together to the same connector...

Again thank you so much for the information. I did the unplug test before getting this info. I will go out and double check with this information.

Thank you Warthog. The meter was dead. I thought it might be the meter and not the wiring. I thought there may be a reason the new meter wouldn't work due to diodes or something for the 24 volt system. You answered that question. I will "try" to figure out the wiring diagram and hopefully fix...

Thank you gentleman. Is there a reason that the original wiring won't work. I know it was set up for 24 volts so I assume there is something there that might cause it not to work.

Thanks rsh4364 said with a laugh. I was hoping to install it to the original wiring connections. Already have the light working using the original wires. Do you have a suggestion for a + that is only active with the key on? I could use one of those splice connectors and run a wire from it to the...

I have a new 12volt volt meter. Tried using the original connections after the rosscommon conversion. Doesn't work no power to the Gray wire. Would like to get this working properly. Can anyone help?

First I would like to thank "rsh4364" and "cucvrus" for responding to my post for help. I finally skinned the bear today thanks to all the incredible information many of you have placed here on this web site. The last problem was the ground wire on the right rear head that goes to the GP card...

I checked the voltage on the GP controller card connections, here are the readings I got. Ignition switch off no voltage to connections: A,B,D,G,H,L,M Ignition switch on: A purple none B light blue 12.6 volts D dark blue none G two wires pink and pink/black stripe 12.6 volts H orange none L...

Got my starter problem fixed. I pulled the new start switch out and found it had power and when manually selecting start the Dog Head relay worked. I did open up the wiring harness to check the wires to the start switch and other wires on the steering column. I am guessing the old start switch...

Made a mistake here.

I replaced the 16ga fusible link wire on the red wire to the starter relay and the 2 wires on the 12 volt harness block on the fire wall. I have power to the Dog head starter relay red wire and good continuity on the purple wire from the dog head relay to the starter solenoid. I have power to...

Thank you so much for answering my question "cucvrus" one more thing I don't have to mess with. This has become a struggle but I will plow on.

This is just a junction for the 12 volt power cables, there is nothing behind it that connect to the bolts on the front???? The reason I ask is I am going to replace the fusible links and one of the connectors in the picture connects to both post. Since I converted it to 12 volts can I put a...