Search results

the hoist work good I have a piece of 1 1/2 by 1/4 strap with a 3/4 hole in each end so I can use a lug nut to hold the strap to the hub and a clevis to the hoist . the strap is about 8 inches long . I have not used this on my m52a2 but it worked great on my m269 low boy' .kenny

I have had fuel lines fail on the in side by collapsing .they look fine on the out side and on the inside the rubber has seperated causing a stopage of fuel after the engine quits the line opens up with out the pump pulling fuel . the engine restarts and runs till the suction causes the...

some times a 12 point socket standerd or metric which ever on fits better will grip a square easy out or tap

I can't read the sign on the door .but it may have belonged to Weninuche consruction out of Cortez Colorado in the late 1980's they had lots of military trucks mostly 5 tons and some 10 tons . this truck must have been used to hual water the piping on the bumper looks like a spray bar .

my m52a2 has the cowl cracked out where the hood hinge bolts . I could use a patch piece for each side if you could cut them off a junk cab thank you kenny

I think trucks with military pant will always draw the attention of law enforsement . when getting my vin numbers checked my tan 1952 m-211 the officer knew it was military but my m-52a2 is white and black and the same officer though it was a commercial truck made by kiaser-jeep . kenny

last year I bought a Herules XHD motor that will go in my 1943 White 666 .the motor was rebuilt in 1963 in France and never put back in a truck .the seral number in the truck I have is about a thousand numbers diffrent from the motor from France . so maybe this motor was used in the invasion or...

I can help or dismount these things and chain the wheels to the frame and get it ready to ship on one of my week ends off . with the truck down to normal size have you had any luck finding a hualerthat could load it where it is ?

i would hate to try and drive your truck to Albuqurque a brake down would leave every thing in a bad spot . my m52a2 with trailer runs about 45mph and with a load it would be as fast as this truck runs . I could get your truck to Farmington and feel I'm not pushing my luck . kenny

Great save . I'm about 100 miles from Dulce and can help getting your truck ready to ship . I know these trucks are wide but I don't know how wide . I have a compresser and tools and a m269 wrecker low boy with beaver tail with ramps if needed .kenny

I used rubber cement after cleaning off the old grease and it made it a little tacky . kenny

If some one buys this truck and needs to store it in aztec . I could help get it there if it is on a weekend I'm off it should fit on my m269 behind the m52a2 if it is not driven or has trouble on the road I could be there to help. kenny

my GMC gets 4 1/2 to 5 mpg at 45 mph .

the m135 rims are made to only go on the hub one way if turned around the lug nut hole is not taperd where the lug nut touches the wheel .I used 10x20 on my 211 and I thought the tire was kind of close to the spring seat but never a problem . 1100x20 will be closer

some hose on the exhaust that runs along the top of the windsheld frame and then under the canvas top to the out side will make keep the noise down .

very nice job. does any one have a part number for a replacement bulb and know where to get them ? thanks kenny

RE: Airpack I use atf to lube my booster . maybe somthing heaver was put in be for you owned the truck

GM 7411327 ratio 1.16to 1 ( single speed ) the shift rail that is hooked up when it is pulled out it is for reverse when it is pushed in it is for driving forward should have a inturnal spring putting presure to pull it in to the case. the shift rail not hooked up is for in gear or neutral ...

I have had some luck using moth balls in closed areas that the bees seam to like to biuld nests . kenny

checking the part numbers these shoes don't fit m211 truck - m52a2 truck- m200a1 trailer or m269 trailer the numbers should show up and fit some thing ?