Search results

The OP is in Germany, not the U.S.

Have you looked in TM 5-2420-224-24P to see what kind of bolt goes in that top hole?

It's good that you at least now have all six wheels airing up to the same level. You are making progress, so don't get discouraged. Are you certain that you don't have an air leak in the system somewhere such that the compressor can't keep up with the leak and the controller is trying...

One other thing to remember is that these trucks range from 25 - 30 years old and most have had minimal or no PM on the CTIS system either during active military use or subsequently. In addition, the M35A3 trucks were the first deuces to have CTIS so mechanics and drivers had no practical...

I think CM Automotive Systems is now out of business. It's too bad, because I've talked to them on the phone in the past and they were very helpful. They even sent me a brand new wheel valve at no cost when I told them it was for my ex-military M35A3. Try cleaning the wheel valve first and...

As HDN says, start with the TM. The CTIS on the A3 is a very simple system. Since 5 of the tires are at the same pressure, to me it sounds like you need to remove and clean the wheel valve on the 6th wheel. They are very simple to open up and clean.

Thanks for everything you do Clint! I finally made it back home at about 1700. Pulling that XM1061Eq trailer with my M35A3 and an M151A2 on the trailer is a bit much. Some hills I was actually down to 10 MPH. Twice I had to go to low range. But, it did work out. I had a very good time, as...

I'm looking for the following: R-442 working radio MX-6707 antenna base AB-15/GR or AB-558/GR antenna Rear vinyl seat for M151A2 in good shape

Where did you find the tires? Did they have new date codes? I understood that Michelin quit making those years ago.

Just about ready to roll. I finally got my M151A2 loaded on my XM1961E1 trailer and hitched to my M35A3. The M151A2 is temporarily tied down on the trailer, so I still have to do a better job of securing it. I spent the last days installing my RT-524 radio, mounts, cables and antenna. All...

I just finished putting the top and side curtains on my M151A2 that I'm bringing to the Rally. What a pain. I also just finished installing an RT-524 radio and antenna. I still have to load it on my XM1061E1 trailer and load my M35A3. I'm still looking for a hill to back the trailer up...

Go fund me accounts charge a fee. I think it's much better to donate money directly so that 100% goes where we want it to go. I'll donate $100.00 at the event. I have attended most of the Georgia Rallys over the years and had a great time, every time. I have no problem helping out. Maybe we...

I'm bringing the following items to sell. 1. One 12-can case of Gillespie (AJP) spray paint that is virtually new, #30118 Field Drab Brown $10.00 per can or $100.00 per case. 2. One 12-can case of Gillespie (AJP) spray paint that is virtually new, #30277 Desert Sandust. $10.00 per can or...

Just completed digging quite a length of trench with the backhoe and everything was working perfectly. Until today when I started the engine to move the SEE to where I normally park it. The alternator isn't charging and the tachometer isn't reading. I imagine the tachometer is driven by the...

I replaced the lines myself with new lines from the local NAPA store, available in many lengths. As far as the flexible hose on the air cleaner, I looked up the part number and found them on Ebay, but listed for HMMWV . The identical same part and cheap and took approximately 15 - 20 minutes...

If you don't have sufficient air pressure to the transmission Intermediate Speed Control the piston won't slide back and forth selecting low and high range. There can be other causes as well. In my case, the piston was corroded and my FLU419 broke down on the highway. It was working fine and...

I'll jump in with my M1030M1 USMC diesel motorcycle..

I have forks for my tractor. I spread the forks just wide enough to miss the ring and then press down slightly on the tire. This gives a very solid steel fork to pry against with crow bars and pry bars. And soapy water of course. I have one 5-foot pry bar that really works well. I would be...

Sorry about your ankle! I hope it heals up fine. We will miss you at the rally. :(:(

I had a canvas top repaired by an upholstery shop that specialized in tops for boats. They did an excellent job and were very inexpensive.