• Steel Soldiers now has a few new forums, read more about it at: New Munitions Forums!

  • Microsoft MSN, Live, Hotmail, Outlook email users may not be receiving emails. We are working to resolve this issue. Please add support@steelsoldiers.com to your trusted contacts.

Search results

  1. Guyfang

    Slave plug for MEP genset - cost effective options(?)

    To encourage learning, it often pays to encourage Experimenten. Unless you were born an EE. or 120 years old. Rich was 18 when he made these carts.
  2. Guyfang

    Slave plug for MEP genset - cost effective options(?)

    Mainly because the guy who made it, considered it a toy. He had free rain to loot lots of Nike/Herc equipment, and thought that it would be a good learning experience.
  3. Guyfang

    Mep802a starts then shuts off

    I wish you luck in repairing this gen set.
  4. Guyfang

    Mep802a starts then shuts off

    Open to read comment.
  5. Guyfang

    Mep802a starts then shuts off

    Even if the LOP, Low Oil Pressure switch is bad, the set should start. The S1 function, in the start position, bypasses the LOP, along with several other safety switches. So when a set can start, and the LOP is bad, you simply put the S7, (Battle short switch) in the up position, and the set...
  6. Guyfang

    Slave plug for MEP genset - cost effective options(?)

    Amperage. 24 VDC, but Series/Parallel wired. Five Tons use 4 batteries, because starting is a tad more work. And when you are on a hill top, (some would call it a mountain, but after you have seen the Rockies and Alps..........) where it often got down to -25 or -30 Cel, and snow bung hole deep...
  7. Guyfang

    803a lost all output?

    My bad. Wrote CB1 instead of K1. Getting old. Yep. Getting old.
  8. Guyfang

    Starter switch for M51A2 5 ton dump

    Is this deal done? Can I close this thread?
  9. Guyfang

    M816 wrecker rear winch 45k lbs worm shaft and more

    Any luck here? Or can I close this thread?
  10. Guyfang

    Pawn Stars look at a HMMWV

    I just love dialects. Here in Germany, its REAL bad. Sometimes two towns a few miles apart have words that are simply not understandable to folks a few miles away. Cracks me up. And when you are a foreigner, speaking dialect, Germans laugh till they fall over.
  11. Guyfang

    803a lost all output?

    Open to read comment!
  12. Guyfang

    803a lost all output?

    So, the set starts and runs. No output. Right? Is there 120 volts on the 120 volt outlets? Yes? Good. No, well, we need to dig deeper. Will the S5 switch, (AC output contactor switch) close the CB1, (Output contactor)? And will the DS7, (Output contactor light) come on, when you flip up S5?
  13. Guyfang

    My new hobby: Wood military vehicles

    My thanks goes out to all my Brothers and Sisters who served.
  14. Guyfang

    GP auction

    I wish you the same!! I sometimes forget it here in Germany.
  15. Guyfang

    Slave plug for MEP genset - cost effective options(?)

    We made another battery cart with 4 batteries on it. Had them hooked up, so we could jump off the 5 tons, and use all 4 batteries. If we needed to jump off a gen set, or 2.5 ton truck, we flipped a switch, and a relay cut two batteries out of the system. We could have just used a second slave...
  16. Guyfang

    VIN location

    My memory of Miles City, is not real positive. Was glad to leave and go back to God's Country, Hill City, SD.
  17. Guyfang

    GP auction

    Bob, There is already a thread started asking this same question. No real answer. But call the Richy Brothers and ask. Thats the only way the question will be answered.
  18. Guyfang

    Scammers yet again. YOU SHOULD READ

    Everyone can help here. If you open up a thread, and there is a email or phone number listed there, send that person a PM. Or tell a moderator.
  19. Guyfang

    Pawn Stars look at a HMMWV

    There are times that not living in the States, has advantages. Pawn Stars seems to be one of those times.
  20. Guyfang

    Armor demil

    You have asked this same question in another thread. According to Forum rules, that not to happen. Please to not start asking the same questions in multiple threads.
Top