Search results

The fleetguard is prefect for a nhc. The nhc250 can require almost twice the fuel that a ld465 deuce will.The deuce has help with an in tank pump, while the 5ton only has the pt pump on the engine to suck the fuel from the tanks. Any restriction can cause lower mpg and we're already in the...

Wix 24309 and 24770 are popular filter bases to add on. 24309 takes the 1"-12 filters and 24770 takes the 1"-14 filters. I guess it depends on what filter you want to use. Baldwin makes a base that has the o-ring type fittings the stock filter uses. The stock m809 filter is a decent filter/water...

My current plow hydraulics are ran off a electric power pac. When I find a pto for my truck, I have a parker P20 pump to install. Most of the older plow tricks at work use a p20 or similar pump. It runs the plow, dump body, and salt spreader. Cast iron gear pumps last almost forever and are...

Anyone have the part numbers for the nylon hinge bushings that OD Iron use to sell? Devilman had a write up that had the part numbers but I guess it didn't make it to the new site. Pic here http://www.steelsoldiers.com/showthread.php?12684-Door-Hinge-pins I've started painting and I would like...

That looks great. Top notch work as usual.

I primed with rusty metal primer a few days ago and when I got home from work yesterday my wife had the green pretty much done. I had to school the home depot rep on federal standard paint. But she seemed intrigued and happily mixed my paint. Didn't do the inside, used about half a gallon. This...

The 11.00's fit on deuce rims just fine.

I'm going to try to make it. Hopefully with the camper and family.

That looks like a completed 4 door to me! Easily convertible back to a 2 seater!

I'm not sure your looking for the right part. I have numbers nsn: 2530 01 125 6076 part: x76-3276-L-12 meritor Alternate pn: ta-0011sba and 84tc266 They are pricey but can be found. Those #'s are for the spring brake can. The non spring can (front) is nsn: 2530 01 091 7814 pn: E3276-L-12

Might as well put bigger nozzles on your injectors while you have them out! Here is some good reading about setting injectors. Hope it helps you out. http://www.steelsoldiers.com/showthread.php?73256-Nhc250-valve-injector-overhead-adjusting

Power steering filter International part fits m809 series pump. Kit comes with filter, reservoir seals, spring and cup and new lock nuts for the reservoir.

Our engines, without a turbo, require 900-1000 cfm. A turbo engine can require 1500+ cfm. I don't think the stock air filter is up to the task of a turbo.

I think your right, that filter should flow better than stock. But I'm not sure if it will filter as good as it needs to. It is designed to be used with an inner secondary filter. Wix 46664 flows about 1000 cfm More modern turbo'd 855's use a filter that flows about 1500 cfm I know our engines...

I'm looking forward to your build. I can't remember how far away you are, but if you need any help let me know. Since your keeping it full length, you could move the transfer case back a few inches and use the drive shaft from between the tandems. That would leave room for an 18 speed double...

Very nice. I've always wanted to put better seats in my trucks and thought about using the same seats as you. Now I know they fit and look great. Jeep seats are easy to find seat covers for. I like the waterproof neoprene because I'm too lazy to put the top back on when it rains! Good work 59apache.

:-?:funny:

The intake was put up high to keep the dust out, desert conditions are hard on stuff. The air filter is the same from the 60's m809 series. I've heard the hmmwv wheel o rings make good air cleaner seals. To check your seal, pour some oil into the air cleaner and seal it up, if it leaks out you...

Ran across some old notes I thought I'd post. Seeing more of these rims around. 24 bolt wheel, equidistant studs Nsn 2530-01-558-3027 wheel, inner Red o-ring pn: 12460338 nsn: 5331-01-417-1043 Inner rim bolt: 12342758 1/2"-20 x2.12 I have a bunch of the nuts left over that fit these if anyone...

Multi fuel starter Original pn: 12493623 Nsn: 2920-00-999-6216 Current prestolite pn: M0017072ME Or look for a 40MT with 12 teeth clockwise Standard 3 bolt flange: sae j542 type 3 Delco is easier to rebuild. Solenoid and nose cone can be rotated to fit most any application. 42MT will work as...