Search results

You will need a serial interface to talk to the module and the software is I believe available on the Dana website...

You can Easily get 350HP out of your 3116. Start with the 290HP governor and turbo modifications general mentioned. Then turn the high speed screw up to allow 2800RPM and delete the air compressor, alternator, power steering and cooling fan... I believe the marine engine is basically the...

That silver one is the gauge sender. The switch Is in the background of your pic(black plastic body against the block, harness toward the rear). Also seen lower right of Matthews pic, against the block, painted yellow. that parts picture you added of the 3 wire oil pressure sensor, looks like...

I believe matthew is correct, 15PSi low oil switch(S27) is on a little manifold on the drivers side of the block a little above the oil pan just forward of the starter... That provides the ground path to energize K11 and the dash low oil idiot light. When it hits 15PSi it opens the circuit to...

Yea MME lost my respect when they took our R&D for a cost effective fan solenoid (~$30), added a connector and some fittings and marked it up to $309...

Good question, that procedure is on the dual vbelt 3116…

Worked fine for me when i did valve lash and injector timing…

With that amount of water out of the main drain, and it never being run in that condition, you will probably be fine as it want straight to the sump and pushed oil up. I doubt it ever came in any significant contact with the friction material. The main housing fills before oil gets high enough...

If it filled with significant water, the transmission dipstick should indicate this(will show it full of fluid well above the dipstick marks. Most anything on the truck can tolerate some water in it for a bit EXCEPT THE TRANSMISSION. The friction material on the clutch discs is bonded to with...

Here is the vent installed, under my dipstick tube. It is lower than the top of the bell housing…

no, the bell housing vent is a hose up alongside the arch that supports the cab latch. There is a small round metal cap breather/vent screwed into the top of the main transmission case, about 18" aft of the bellhousing/cab arch. It is only marginally higher than the top of the upper chassis...

There is a little air cap/vent on top of the trans housing. If water got that high, the trans probably has water in it. Do not roll over the engine or trans until you confirm no water in their oil. Water kills the clutch plates. First check the dipsticks for excessive level, then drain the...

Yea sounds like a restriction, and perhaps a leaking wheel valve. Pressure should equalize fairly quickly each time it cycles, if it is not, ctis will fault, same if it is too uneven at the start of a cycle, pressure equalizing causes unstable pressure and the unit faults, so it takes a few...

Only one gasket sees water/coolant, the cooler to block gasket, the other gasket only sees oil filter housing side to cooler outer face…

Yep, that's how you do it. Old school but fairly common way of getting engine RPM off a diesel... I just don't think the A0 alt is capable of it. They have that terminal configured for AC on the A1 alt and the LBCD monitors alt RPM using it to make some of its decisions...

On the A0, that second terminal on the reg is not labeled AC, it is labeled F- and is intended to monitor the duty cycle/pulse width of the pulses used to excite the field (How hard the alt is working). Not sure what freq it is being pulsed at by the regulator, but I suspect it is not...

Not an automotive tach, those are typically sensing ignition and are only looking for 1/2 pulse per revolution per cylinder, I E: a V8 has 4 pulses per revolution. you need a flywheel/magnetic pickup tach that can sense the 133 pulses per revolution created by the sensor monitoring the passage...

Thats good, but the ABS modulation valves are inline and could be effecting final output even if ABS is not activated. The only way to confirm this is with T fittings at the cans and pressure transducers looking at the final pressure actually reaching the cans.

There is actually 2 RPM sensors, one lower right belongs to Allison for transmission control, and one top left just to the rear of the primary fuel filter/primer, to drive an electric tach. a mechanical tach? Cant think of any place to get rotary motion from to drive one. One reason no one...

Providing everything is aligned correctly and delivering to spec. You need some T fittings and pressure gauges/transducers to confirm the pressure end, the rest is mechanical. Shoe free space(.026” center shoe?). wedges have a limited amount of travel and if the mechanical alignment isn’t...