Search results

Blazer has been pulling to the right for almost a year, 80% of the time. Drives fine 20% of the time. You literally could take your hands of the wheel - it'd drive straight down the road. But Now It's starting to drift on me to the left now. What I mean is when it's pulling to the right...

gm 14067420 or 23183 Is the replacement check valve a steel ball? When I had my IP rebuilt I swear the fella said he used an upgraded check valve for the return line.[thumbzup]

I just experenced a total dead and I found the fusible link between the Positive 24 Buss terminal and the Ground Buss block under it. I hate these Fusible links. This one already had black electrical tape around it gooy

the 400 turbo automatic transmission dipstick and dipstick tube can be had at a gm dealer.

I paid a whole $10.00 for a RUSTY electric tailgate. I stripped out just the scissor lift and motor. The CUCV Blazer has an identical set up as the Civilian Blazer. Matched up perfect. $10.00 for heavy gage wire for power to motor, $6.00 3 way Momentary Switch from Napa BINGO! I had to PB...

do for a diesel I don't know wayne just have to. :deadhorse: Initially If you just Turn The Key NO START It's not mine it's my 75 yr old Grandfathers he runs it almost DAILY I have started it only by holding the pedal to the floor! He says he does every day crank for up to 20 seconds! I...

:rant:Told you bro I also would go with 4 inch cut the fenders :deadhorse:

HA HA HA Boom! rofl It's called water water water and plasma cutter like brother used on a tear down. I'll probably use the hole saw method as stated - much safer!

I was thinking a piece of thin steel or diamond plate perhaps then a few self tapping screws and some pop rivets for good measure and wall lah[thumbzup]

I know the plugs are good, I put them in. The old ones tested fine with the test light end to the tip of the GP & alligator clip to diamond shaped 12 volt terminal block (right above GPR). 75 year old Grandfather wanted brand new plugs regardless, at the same time I did the 12 volt Resistors...

As I believe it was Westech who quoted a while back that you can get to the Fuel Sending Unit and the strainer/screen/sock by cutting a hole in your bed. Here are some pictures courtesy my Brother Mark69k20 sent to me for a family member having issues with start up. We see no fuel leaks anywhere...

Looks great little bro [thumbzup] Need ya to paint mine next time you come up home. Post should have been titled AF man - paints Wife's 10 09 - MC Green, Risks 4 point of contact! Hope she likes the color or your getting your 6 TANNED rofl

To Whom could assist :!: Seen the link http://www.roscommonequipmentcenter.com/news_notes/nn10.pdf a few years back to convert to 12 volt, very well done. My Father bought a beautiful M1028 with very many new parts. To bad Mother wanted it Un Militarized and painted. So we did and did the...

quote=4trans;599717]Maybe the tow rating is lower cause during R&D testing they bent the frame rails at the firewall and had to load it on a trailer and take it to the nearest Chevy dealer and have the rails replaced Good one... anyone have anything to add on new Ford 6.4 L just came out...

1. BDS ? Brain fart 2. 4 or 6"? 3. Cost Thanks...

What kind of lift setup did you use?

no it's not a required part! It serves only as an EXTRA barrier "pre cleaner" to the actual air filter. The military had it over the air filter for an EXTRA protection because of the potential for training/missions in dusty conditions.

I don't understand what you mean "a screw in heater"? You do have to tighten up a screw to expand the rubber plug once you install the freeze plug TYPE Engine Block Heater. Don't buy the Dipstick heater JUNK, stay away from the bottom Radiator Hose coolant heater. Do a block heater at the 2ND...

Alright, you told us that you smelled smoke! Pulled the Glow Plug Controller CARD. It was burned in SPOTS. So you replaced it with one you purchased from Ebay. Why would you install a part where you knew you had an issue? Pull that GP Control Card out please and get back to us. Let us know...

There's a good thread on the fuel filter change out One person [thumbzup]using a bottle, couple feet of hose. Watch his Video http://www.steelsoldiers.com/cucv/30327-fuel-filter-changeout.html