Search results

Lots here have run remote axle vents to fix this issue

I'm having trouble finding shims..... Do ya'll think large bore A/C shims will hold up? The shims for adjusting air gap for the clutch, the older cars had larger ones than the newer cars do, and I happen to have a assortment of them that I could probably make work. They're almost the same size...

I got a adapter all cobbled together for my injectors to fit the shops pop tester and have tested all my injectors. I have one or 2 that are only spraying from one port, all seem to leak 100psi before they open, and my opening pressures all vary from the lowest being 2500psi to the highest being...

Carbon!!!! So I pulled all my injectors last night and I'm suprised it runs as well as it did with all the carbon obstructing the tips! I brought my bore scope home wanting to see inside the cylinder but couldn't make it that far in due to it. The pics show what I'm talking about. So now I also...

+1 I too have a full rear set of thimbles if anyone needs some.

Is there not a 1/8th allen adjuster in that small hole???? I saw some info just last week where they were talking about which IP's had smoke screws and which ones you had to adjust the angle on the cam in the IP. Now just to find it again........

I put a row of magnets out of a junk starter around my final filter to hopefully catch any small particles.

Good job of documenting these issues and fixes guys. Just might come in handy one day! Thanks!

Hey thanks, but no need I just found some here close, I should have called them first! I'll share my source and price after I get the ones I need.

Good looking truck Tomcat! I finally got back to my hoist project I ended up mounting it a little differently than planned. But I got it mocked up and tested, it held fine no flex from the bed with the backing plate I used. The backing plate I made so long so I could attach it to the frame if...

Son of a ***** I didn't see anything on the site showing that but sure enough I tried to put them in the cart and it shows none in stock!!! Well at least it shows the Abac part number maybe I can find some if needed with that number. I read through the TM suggested by eagle and got alot of good...

From this thread http://www.steelsoldiers.com/showthread.php?107021-Fuel-Injector-Issue-LDT-465 new nozzles are $1 if I can get the correct ones from this place http://www.american-milspec.com/p-291-new-fuel-injector-nozzles-ambac.aspx Now just to pull them and cross referance my part numbers on...

Coastal Diesil quoted $40 to test and $60-80 a piece to rebuild depending on tip price! Seems to me someone found new tips on ebay any pointers on how to find the right stuff? And would it be good to change to 2 hole tips or is it more differances in the injector than just the tip?

Thanks! Now I've figured out why I was missing stuff with my TM's, I didn't download them all! Fixed that now and thanks for the info. I'm going to look the TM over tonight and if it looks like something I've got all the tools to do I'll be sure to take pics of rebuilding them. If not I'll have...

Don't feel bad I thought he was serious too! I'm teaching my youngest brother to drive my M35A2 (full size) and he's only 12 I think???? Just in the fields and on dirt paths so far but he's learning. Put it in low and give him the pointers. It's really helped him that you don't have to worry...

Good idea, I've got a couple friends at 2 different tractor shops around town I'll try them.

I would like to test/adjust/rebuild and clean my injectorsbut have some questions. Anyone out there got the Injector rebuild TM or info otherwise on how to do it? I haven't seen that info in the TM's I have down loaded. I have axcess to a pop tester that I just have to adapt to my injectors...

Done that to mine some time back.

Subscribed, I was having high egt issues limiting the amount of throttle input also. I also changed all fuel filters with no results, tried up and down on the FDC adjust screw, tryied looseing injector lines to kill single injectors. Finally I backed the FDC adjuster all the way off untill the...

Bump Anyone else attending? I'll be there Sunday, not sure if I'll drive the M35 or a normal truck.....