Search results

Does anyone have a lot of knowledge designing and sizing turbos? I have a 9.0 litre diesel that will not be run at 2500 rpm in a m-35, and want to choose two water cooled turbos for it. I do not want any more than 8 psi boost. i know there are many other input criteria and i am working to get...

MEP-003 freq meter goes from 0 to full scale and back to 0 as unit starts, stays at 0 while in operation. same when shut down so i assume the transducer has failed. has anyone else had this happen? tom

For what is worth, i have seen a couple burned 802's and heard of others. While servicing one of mine it developed a fuel leak in the hose that is the return line from the injector pumps up to the injectors and back to the fuel tank. This is 4mm hose and when examined, it is rotten and cracked...

Located on the left side of the voltage regulator, there is a large fuse holder. Apparently most do not have this fuse. Unfortunately it is missing and I can find no info in the manuals about what amperage fuse it takes. Hopefully someone else has a set with this fuse and can read the specs from...

would someone post the direct link to the lister petter parts site? not to the home page, but to the actual parts page?

just thinking about past trucks

the exact correct gaskets for the fuel filters on mep-0003 are available. i researched this since the replacements many other filter companies say fit DO NOT FIT. fram part number SP101489 can be special ordered from tractor supply or walmart. (free shipping at walmart) tom

i built this truck a few years ago out of mostly new parts. the pictures have been compiled and posted to part of my web site. a lot of them are of the original build and a few like the heat and a/c are later. since it has all 3 air locking axles i got a new data plate for a m-621 and call it a...

has anyone else had problems with interstate 6TL batteries? in the past they lasted for 5 - 6 years for me. in the past 2 years they do not last over 1 year even with light use. tom

ok, i have 3 original military rockwell air lockers in my truck and am seriously thinking of bobbing it. so i will have an extra axle that is way to valuable to just scrap. question is what is it worth? would some one else bobbing their truck want to buy it? just wondering. tom

original prototype, .71 od gear set M-35 OVERDRIVE UPGRADE KIT FOR .71 OD SPICER 3053 M-37: eBay Motors (item 190444132440 end time Sep-20-10 07:33:43 PDT)

has anyone bobbed a deuce by simply shorting the frame and bed by 3 feet? i would like to see pictures. tom

how many people have replaced head gaskets in 2009??

is there a manual on this site for this engine? specfically for replacing points and retiming the magneto. tom

hi, being a m-35 person, i only know the m-1009 from a distance. but i do know of most of it's civilian counter parts weaknesses. so, is it possible to find one with NO rust around the edges of things?? tom

some had speculated that mounting an a/c compressor on the deuce would be rather difficult. almost finished, i can say that it was surprisingly simple. still need to make rear brace, but have template made so just have to shape the 5/16 plate and drill holes. update, compressor finished...

so there is a snap ring on the front of the water pump shaft. should i assume the pulley is on the shaft with a key and will just pull right off?? has any one taken one off before? i'm going to make a custom pulley to drive an a/c compressor..... tom

several data plates i have say the same thing, 32 qts for cooling system. drained rad and block, no heater, will only hold 22 qts. where does the other 10 qts go?

so i finally had time to do a definative mileage test. something scientific, no guess work like how full the tank is. around town 30 - 35 mph stop and go, 7 to 8 mpg varying traffic 48 to 52 mph, 10 mpg steady 45 mph rolling hills, 12 mpg steady 55 mph rolling hills, 12 mpg loaded with 8,000...

have not seen this info posted yet. how about a site map, or a link and some info.........