Search results

Well the "step on brake hard" part of the power steering pump test was too much for the 28 year old piston seal in the Hydroboost unit on my M998 and it started leaking between the master cylinder and the firewall. A quick look around and the replacement cost was too much for my cheap a$$ so I...

Please forgive me if this has been discussed before but a search did not turn up anything, So I was checking out a company that sells water pump parts and noticed the impeller was different on the civilian 6.2L than the 6.5L, the 6.5L was slightly larger in dia. and the "fins" were laid out a...

OK so I bought a HMMWV and I have turned in the EUC and Hold harmless affidavit, but the sale says "release date 4/9/2020", this was payment date,,, am I wrong or does that mean I can pick it up?

So I am replacing the leaking fuel pump today, was hoping for a shortcut like the gasser gm engines but apparently no such luck, so after using my head to break the fall of the fuel pump rod on its way to the floor I noticed the rod looked rough as in broken on one end, managed to coax the other...

I need info on the mounting of the S-788 shelter, on the download page there are several available for the S-250 but no downloadable files for the S-788. I have some pretty clear photos of the rear mounting using the air lift bumper, and they are substantial but nothing about the forward mounts...

The 200A install is pretty straight forward, but I thought I would hit the highlights using a NOS 200A install kit and a used 200A alternator, I did not take any photos during the actual mounting of the alternator will try to remember the wrench size for each bolt, there is an eclectic...

I am surprised I did not find this trying several searches, does anyone have the vendors/numbers for the civi replacements 10K half shafts? I would prefer NOS shafts but am concerned about the condition of the boots.

I did not buy a "Red Dot" Sanden compressor, but I did buy a U4311 which is supposed to be the correct part number. Problem is the pulley supplied with the Red Dot kit has a 3/8 belt groove just like the rest of the belt grooves on the HMMWV, the belt supplied is a 10Axxx which is 10MM wide. The...

I can think of several projects I could use these clamps on (pic from Fleabay sale)

Can the neutral switch from a 3sp shifter be swapped into a 4sp shifter?

OK so what are you using as an on board air system? 12V or 24V would not matter to me, I actually have some belt driven pumps but I think there are enough belted items tied up to the water pump already. I would like something with a reservoir and a pressure switch, I see these online running...

OK I will admit, TMs and I do not really get along, they are put together by a mind that makes little sense to me. BUT I have looked and cannot find a depot level repair manual for the NP218, or am I just missing something? I have the parts manual with the exploded view so I can most likely...

After my little run to the beach last weekend my old bone on bone knee was killing me so I decided to do "something" even if not the most ideal solution. The factory hand throttle does not have enough travel to be used as a cruise control so I dug around and found a Vernier control from a...

OK so when I went looking for door locks the "factory" only had 2 @ 18.00 ea. so before I even received the factory handles I bought the other two I needed off of Fleabay. I did not have anything to compare to so I bought junk some moron hacked out in his garage, he/she drilled a hole in the...

OK so I am sure I am not the only one to scratch my head looking at the side doors on a helmet top, what in the world were they thinking?? you would have to be 8-9 feet tall to comfortably access the full area of the boxes. So this weekend I decided to do something about it, the first thing I...

Well I just picked up a M1101 and it does not appear to have had any MWOs done to it. So is there a source of MWO part kits? EDIT, OK I may not need to do any MWOs, I don't know the exact year of my trailer yet but the others sold at the same time were manufactured around 2009 I believe so all...

Is this the mount for the Delco style "pancake" compressor? I am trying to help out a seller, the "kit" has a Sanden compressor but this does not look right Edit, sorry I should have listed this in the 5 ton up forum, please forgive me...

I found this, it is for the M1113/1114 but at least it is complete and one ONE page. I tried to post on the TM page but could not attach. I am sorry if this is redundant I have the complete TM-9-2320-387-24-2 but it is too large to attach.

The previous owner had stripped the electric winch off the front of my M998 leaving the front view rather bleak. A short time ago I asked if anyone ever built a front bumper in the same style as the airlift rear bumper I had just installed on my machine, of course it was not needed as there are...

When these fail what is the most common issue?, open windings, diodes, brushes, regulator???