Search results

going with regular bulbs on 1102, 14 marker lights now my 116, I replaced the blackouts with three leds (36 lumins each module) and wired for backup lights, and used two for running and five for stop and turn in the gutted housings , GL was nice enough to make sure they bent them so I had...

When I saw it I knew that was it, the rim is 1.5 inches smaller than the main body of 8 inches, so is it using the diference to push the oil out, because it's a function of RPM and Diameter with the average thickness of fluid in there to. for a low mod rotor a CO2 tank or Fire Extinguisher ...

Centramatic wheel balancers install behind the wheel. Once installed, centrifugal force causes the shot and oil filled aluminum balancing ring to automatically balance the tire and wheel as you drive down the road. Wheel Balancer FunctionThe free moving hardened lead alloy shot is bathed in a...

the trailer end connectors are right under the front edge, My plan is to replace with flat 4 one and cable for now and keep the original with trailer. This is for a friend to use so just changing bulbs and no changes that can't be reversed. Temp lights that you know work and magnets help, I...

Component Specifications •Standard 3450 RPM Motor: •1/3 Horse Power •250 Watts •60 Hz •120/230 Volts •1200 G's •Custom 6000 RPM Motor: •1/3 Horse Power •250 Watts •50-60 Hz •120/230 Volts •Up To 3600 G's •Centrifuge Bowl: •22 oz Capacity •8" Diameter x 2" Deep •5.5" Opening at top •3 Drain...

ment to say it pulled well with my swb silverado, what are you towing with, if you don't mind that was before i got a riser for pintle hook, I saw one in Perry and had to have one still not level but better

Did you pick up from Albany, I'm wondering what is in the Box

the tm is in the aux equipment section i think, http://www.steelsoldiers.com/forumdisplay.php?95-Technical-ManualsTM 9-2330-392-14&P

Thanks, after looking around some I see more of what is being done and marketed, that was my line of thinking that fluid should come in closer to center .

§ 730.7 LICENSE REQUIREMENTS AND EXCEPTIONS A relatively small percentage of exports and reexports subject to the EAR require an application to BIS for a license. Many items are not on the Commerce Control List (CCL) (Supplement No. 1 to §774.1 of the EAR), or, if on the CCL, require a license...

http://www.steelsoldiers.com/showthread.php?32234-16-x-16-Military-tent-Frame&p=799545&viewfull=1#post799545 looks like he has been there and done that,

http://www.galco.com/shop/Subminiature-Circuit-Breakers http://www.galco.com/shop/Cord-Grips not recommending, just first ones that came up,

Redirecting the flow is not going to help in this application, . would like to see ideas on your inside to trap dirt and the exiting of cleaned oil, maybe in another thread If you don't mind some questions

voltage reg is used on kato genset http://www.wbparts.com/rfq/6110-01-206-2358.html USED ON SHIPS SERVICE GENERATORS MODEL 4P20963

TRAINER'S GUIDE FOR M2/3 BRADLEY FIGHTING VEHICLE SYSTEM MAINTAINER Thanks PT,

just messing with you, compression, fuel and spark . might be some more work they forget to tell us about , :-D

looks like that has been hot , maybe a bare spot under it, also have you tried each battery by itself, a bad cell maybe

The Commonwealth of Virginia encourages recycling through technical assistance, recycling tax credits, and educational and program grants,

Just a thought, the turbine and impeller spinning at close to same speed give a high circular flow , just thinking it may tame the incoming fluid . guessing about 10 pounds oil and the converter spinning , it's some good fab work and he is having fun it seems with tuning the process. I like...

Opening pressure should be 1950 ± 25 psi for a new nozzle, never really worked with a Diesel', Think I got lucky on my Mep002A to learn on. 2000psi takes a pretty dedicated set up to work with these things, ,..[thumbzup] Jerry