Search results

Have you ever changed or tested them? If you don't know how the TM 9-2320-289-20 tech manual has a step-by-step on how to do it. Do you have a multimeter and know how to use it? And is the GP resistor pack still installed on the firewall?

Sure seems like a lot. I would bet a few have burnt out.

Welcome to the site. Moved you question to its own thread. Before starting any electrical troubleshooting you should make sure your batteries are up to snuff. That includes a full charge and load testing. You can do that yourself or have a parts store do it for you. Looking at your battery...

Thanks for listing the part numbers. I just checked and most of the part numbers reference the Wilson rebuilds. There is a known issue with the Wilson units as many have not been rebuilt correctly and cause shorting of the electrical system. The cause is that they have not been rebuilt as...

Which version do you want? The older M809 series with the manual transmission or the newer M939 series with the automatic?

Well there you have it. Thanks

While I don't have his direct contact info you can click on this thread and then click on his user ID. You can send him a Private Message (PM) or an email http://www.steelsoldiers.com/showthread.php?62594-M916-M920-Tech-amp-Tips&highlight= The thread shows one of his toys.

Here is a thread about starter cases and a source for a new nose cone. I just googled "27MT Nose Cone" http://www.steelsoldiers.com/showthread.php?114902-Starter-cases http://store.alternatorparts.com/partno511111delcooe198556710496538lesternos6343.aspx And I did check the Oreilly's link for...

Welcome New Member from Ohio. Good looking truck.

Member M920 is in the Chama, NM area and has the equipment to make the haul. However I do not know if he is in town at the moment.

One of the trucks I picked up had a similar filter issue. You will want to check you fuel tank also.

Here is a list of all the ground location. A lot of good info in the CUCV Helpful Threads sticky. http://www.steelsoldiers.com/showthread.php?120289-CUCV-Electrical-Ground-Locations On a stock system the main ground comes off the front battery and goes to the bottom terminal block behind the...

The heater switch is shown in the TM 9-2320-289-20P manual, diagram #208, item #7. GM 16015256. NAPAs Echlin Brand ECH HC100. http://www.napaonline.com/Catalog/CatalogItemDetail.aspx/A-C-Heater-Blower-Motor-Switch/_/R-ECHHC100_0460583826 I would replace it first before replacing the blower...

Please download the FREE technical manuals for your vehicle. The wiring diagrams are in the appendix of the TM 9-2320-289-20 or the TM 9-2320-289-34 manual. You will also need to read the first few pages of Chapter 2 - Troubleshooting in either of the above manuals to help you understand how to...

More that likely your heater switch on the dash is also bad. They are a known issue . Did you also know that the fuse for the heater also controls the GEN1 exciter circuit? If the fuse goes GEN1 will stop working.

Or you can just look in the TM 9-2320-289-20P Tech Parts Manual, diagram 206, item number 13. It shows the GM part number as 22020945 Using NAPA's interchange option it shows two different options: BK 6551076...

Post number 12 shows the two styles of support brackets. http://www.steelsoldiers.com/showthread.php?15551-Starter-bracket-bolt-size The support bracket for the direct drive starters are no longer available from the dealer. However it seems that CUCVRUS has had some made and is selling them...

You can get a replacement nose cone for around $20. Barrman has posted the part number before. You are lucky that the engine block didn't break. I have a low hour 6.5 that has a broken mount ear.

Many members have done the 6.5 swap. There is even a write up on a couple of them. Here is one from the CUCV Modification forum http://www.steelsoldiers.com/showthread.php?105875-Turbo-time!-Installing-6-5-turbo the shop may be talking about the oil return line for the turbo. Easy to add to...