Search results

That's funny, Ron. I knew exactly what was going on with the high rpm before reading through your post. I was not so funny when it happened to me when starting the first one on the trailer when it got here, since I had no clue how these things work. Also, you may want to leave the outrigger...

I ran a 3/4-inch impact off the wet tank on the Pete, maybe five gallons worth. No, I couldn't do all 10 lug nuts in quick succession, but it worked well enough. Hose size and compressor output seems more important than tank size. Also, not all pneumatic impacts are created the same. Can't...

I liked my 3/4-inch version enough to also buy a 1-inch. The 3/4 was NOS and quite affordable, but the 1-incher was bought used. Either one is great, but I wouldn't use the heavy and cumbersome 1-inch if the 3/4 would do the job. Either way, your 40 gallon tank is likely not the issue. A good...

I would leave them dry, as intended. Whatever you put on there is likely to attract dirt, and it's doubtful that you'll have to remove those pins again anyway. If anything, machine them down a few thousands in diameter if they're a tight press fit. Slop doesn't matter in that application. On...

Once you get one of them out it's easy enough to drive the other one out with a drift. Just don't use a large one and risk mushrooming the inside, too. And the outrigger must obviously be well supported for the hammer blows to be effective. Worst case, start drilling through the remains and...

I fought a pin on the backhoe bucket much like your situation. I think the trials and tribulations were documented in the owner's thread. Anyway, I never resorted to heating anything, but did apply 50/50 ATF and acetone over a few days. Also, to avoid mushrooming the pin, and to create a way to...

Now that I know how to do it, after a fair amount of experimentation, it's quite easy. Basically, remove the spiral snap ring at the top and drive the rod out of the plate. Next I'd remove the hose from the bottom, which is relatively easily accessible at any time during the procedure. Next I...

Alright, I did finally succeed in removing the 3-stage cylinder. While it's in the hospital getting resealed I'll tackle that uncooperative outrigger again.

Anyone here that has (successfully) removed the 3-stage cylinder from an HMMH's forklift? That thing is fighting me. Makes trying to figure out why a SEE's outrigger won't retract seem easy in comparison.

In your case, no. But they should, since as you can see in the little junction box, they're wired in paralell.

On top of the cooler.

Never did try if a 419 implement would fit, but what was on my MB 4-94 sure looked the same. Think I even measured a couple of distances just to see if they were the same. Haven't removed a backhoe yet, but as I recall, the rear mounts also looked a lot like a 419's. Makes sense since this...

Should be standard Stanley stuff. If the jackhammer is also a Stanley, which I don't remember.

That's because you didn't turn the ignition off first, like you're supposed to. After shutting the engine off, obviously. By any chance, did you turn the master switch off with the engine running?

Wish I had that problem, instead of the opposite. One of mine doesn't want to complete the circuit like it should. Anyway, spray a penetrant of your choice (as long as it isn't WD-40) down the hole and see if it frees things up.

I don't know the model numbers off the top of my head, but the forklift for an HMMH uses the same mounts, as does the dozer blade for an HME. And I would imagine that there are many other implements that also fit, since the MB 4-94 I recently sold had the same style mount, in addition to the DIN...

Well, I ran a low flow skid steer snow blower that way for a few winters. Keeping it at 1,800 to 2,000 rpm to make the 'blower run efficiently understandably made the fans come on, though. That has only happened once or twice while using the backhoe. Should be easy enough to add capacity to the...

Not hydraulic related per se, but the 419 can accommodate a dozer blade or a forklift in the front, not only a loader. For the rear, instead of the common backhoe, also a crane or trencher. But the size and shape of the toolboxes won't allow things to to be completely interchangeable between...

For electrical I use various products, including but not limited to, CRC stuff. When a penetrant is needed, nothing seems to beat 50/50 aceton and ATF.

After reading the TMs, and maybe the owners thread (where all these things have been addressed), you should consider running over your can of WD-40 and get something that works. The world of Unimogs, and especially the FLUs, is not a Better Homes and Gardens environment.