Search results

Is there a breakdown/exploded view of this? I know Im going to have to do the brakes soon.

For FYI, might try using the jack on an axle with whatever size tire hes running. I found out that my jack didnt work one nite. Not because the tire was too big but because it was to tired and couldnt lift the axle off the ground. Just a suggestion.

I used a craftsman cordless drill and their ez out set. I used it about 5 times in a month. I got pretty good at it. Might have to take the bell housing protector off too, about 5-6 bolts. Plenty of room. Do a small pilot hole first btw,and then use the ez out. It worked like butta

4 nuts on the drive shaft-to-u joint holder thing (ran out of coffee this morning, giv a brother a break). Get some new u-joints anyway and replace them since u really dont know when the last time they were replaced. Get the nice ones too, your shafts and pumpkins will thank...

Mine died this past winter and I installed a new one. I spliced into the heater line and the bottom radiator line. 1500watt and it stayed plugged in all night. I'll say while its cold out, like really cold, you could pop the hood open and after 10 min you wouldnt be able to touch the thermostat...

The steel line coming out of the fuel tank crosses over the frame in the area of the pass side rear tire. When it crosses over the frame rail there is a rubber hose used with a couple of clamps. The steel line is also famous for collecting rocks and debris which acts like sandpaper in that area...

Whats in the truck right now?

Cant he jumper the solenoid with a heavy gauge wire and make the solenoid work? All u would need is a jumper wire about 4in long and contact the terminal on the solenoid coming from the balast resistor to the other large terminal (I have a manual setup and not real sure what the oem solenoid...

RE: 6 tl Went with the yellow/gold edition batts from autozone (4blocks away from house). 1000ca down to 32 degrees and then its 850cca below freezing. Top and side terminals too. 3yr no bs replacement for $157 american dollars. Napa doesnt stock anything that big and Wal-eyworld's bigger batts...

The pump was reinstalled/replaced for a mere $1280. I wasnt moaning so much about the $650 for +tax/labor but the $608 for the rebuild was harsh. The pump thats on the truck now is the DB2 4267-R. Whats the numbers come out to mean, ie whats the application?

DO NOT (!) use a chevy 350 starter bolt in its place. The bolts they sell u at Auto-zone aint hard enough but for a few starts and then they snap. Go to a chevy dealer and tell them you need the 6.2 starter bolt. Hell get 4 of them and keep the spares in the glove box. A few months ago I went...

RE: it Gentlemen, Provided for your approval... http://www.dieselplace.com/forum/showthread.php?t=36285

Search the forum. I thought u made the mod Cattlett and said it was a noticable difference with how quiet the motor was. Had pics too. I saw this issue on the Diesel Page and I believe some guru had taken a early 70's muscle car air filter housing that has dual ports instead of single. Like...

Wolf... tell me more about the 92 6.5 injectors. They match with the 6.2's pump output? Is this speculation or can anyone confirm this? autozone doesnt carry them anymore but Advance does... at $58 apiece for stock injs, $700 for a set of aftermarket. Chuck, as I understand the turning up...

as I understand the guys who work on our ambulances are decent mehcanics. Hobart Truck got my bid for the Blazer so I took it over to them yesterday. I told the fella that I hadnt driven the truck in a couple of weeks (2) and it took a bit to get her to start. Hes checked the wellmans and said...

If the NY statute is as it reads then: you cant buy a firefighter edition or police edition Harley Davidson in that state and ride it without the risk of being cited? The 2003 jeep Willys with its proper sticker package can be cited. Anyone driving around with a 9/11 FDNY memorial sticker who...

I know it sounds elementary but my old man was an electrician. He rambled on all the friggin time about connections, contacts, dirt, and dust. He always said bad connections whether they were loose or corroded would always cause heat and resistance. It was like a blocked pipe, you could have a...

RE: m1009 battery zap Where does one procure fusable links? Autozone maybe?

"Cheeter tips"?

The Cold advance solenoid isnt working would be my guess. I think its the pink wire on top of the injector pump. Disconnect it, turn the key to the accesory position (turn the key to where the veh has battery power) and then place the pink wire back onto the terminal where it belongs. You should...