Search results

It's what I would do. If the short concerns you, pull the horn fuse.

The fuse boxes are my own for my use. The little thing is a jumper of some sort, with something small wired between the ends. I thought noise filter myself. A write up would be great. I am worried about over grounding mine and making the alternators work funky. I wonder if I can use the back...

No good reason really. I don't really understand the blackout lights, and would use running lights, so I want to remove them. I'm still not sure I understand how to bypass those two switched.

Sure, run the horn off of a spring loaded, momentary, return to center, type toggle switch. I went this route just now myself. No power from the horn switched wire, and my horn was bad. New horn, new relay, new switch. Total outlay, about $25.00 if you have wire, terminals and a crimper /...

Ah heck, just JB weld that starter in there. Glob it all over, every where the starter touches the engine, then brace it in place until it dry's. Once it's dry, mix about 100 tubes of the stuff, get a putty trowel, and really epoxy it in place. JB fixes everything, except marriages.:-D

Doing a bunch of wiring under my hood and dash. Have the two extra fuse boxes in, one under the hood, one inside. The one inside controls the switches to the relays powered off the one under the hood. The one inside is powered off a relay that is fused out of the engine compartment box, and...

I've mounted the plates, and put a light over the rear. Will this pass NYS inspection?

I'd like to lose the blackout lighting system.. The lights I'd like to change to 12 volt and use for running lights. The switches I'd like to just remove. Then I'd like to have the headlights work like a civvy truck. Also, can I just remove the data testing port and tuck the terminal up...

All the radio stuff is gone. I think msoumas will be getting it. If not, someone has dibbed an antennae mount.

I have a whole slave cable set-up, out of my cucv. From the cap back to the end lug of the cables. I also have both antennae mounts. Lastly I have the spare tire mount, just not out yet. I would like to find another front blackout light, to put where the slave cable hookup was. I want to...

Just thinking of some of the hunting sites I frequent. They have a "pay it forward" spot besides the classified. I was thinking we could have one on the tops of these forums for each vehicle class. Like this: I have a..., if anyone needs it, yours for shipping. In return you find something...

Having needed a part now, I wonder if we could have another wiki at the top, for "parts I have, willing to part with...". What do you think?

PM devilman. I'll be getting mine and hopefully it'll fit.

Why not studs coming out of the block when the threads are iffy. Use a retaining compound or epxy on them, They'd still be removeable with propane heat to soften the adhesive.

they still list it, price seems reasonable for the whole unit and filter.

My speedometer needle swings below zero at rest. Is there a pin that should be there, and if so can I place a new on there? If it's not repairable and no longer accurate, I have access to a used gauge cluster out of a civvy truck. Can I swap just the speedometer into mine? I remember having...

I won the one on ebay. I hope it turns out ok. Did devilman nine sixer find one yet?

Got a bid in on an 85 blazer shaft, hope it fits and I win.

Another idea, and I'm doing this to mine as a pre-emptive repair. Go to ebay and buy a set of 4 hummer military battery clamps. Then when they come, go to a welding outfit and have all your cables remade with welding cable, 1 gauge, with lugs on the ends to fit the new battery clamps and the...

What would all want for a drive shaft? Gotta know so I know if I should bid on ebay or not. The shipping is a killer. Up here I really need the 4x4, quick.