Search results

This what I found on short notice...but like emmado22 says get the nsn and also get manuals if you do not have them already. Good luck. Try TM9-2320-280-24-P1, figure 235, item #24, clip spring tension, Part number:12339596 or for a blast sheild on the antenna: figure 237, item #6, sheild...

I heard about this at the Clare show and thought I would spread the word since it was unknown to a lot of people. I found this information on the mpva site... Indiana, September 14 & 15, 2007: Salute to Victory Show, Auburn, IN at the WWII Victory Museum, located off I-69 at Exit 126, hosted...

Hi Everyone, I finally got to put some faces with names at Clare! There were some really nice trucks and a few jeeps, some for sale. I had a great time and sold most everything! I took a few pictures including rainy Sunday! The other humvee is Joel Gardner's. Auburn IN is the next close...

I have been to Iola around 4 times and that is a great show. The GLMVPA Clare Show started small but I believe it is on the way to become a Iola size show. There is always some very good deals to be had and more and more vehicles arrive each year. I also think that this great site and other...

I lock the door on the Mog and leave the window open so my doggie can look down at them while they try the handle. Her name is Nipper...for a reason! On most mv's I have, I have a disconnect on the negative battery lead. This has saved my batteries several times due to my lack of memory.

67Beast, Can you make white vinyl lettering, 2" tall, normal spacing: T. Gates I would like to put it on my windshield... Last night was right front tie rod ends replacement. Now I can start packing the truck and trailer with parts, tools and things to sell to support my habbit! Regards,

I will be heading up Friday morning around 9am straight up 127 from Lansing. I will have my M1037 hmmwv with CDN101 trailer or Lane's water trailer in tow...depends on Joel's schedule Thursday. The cdn101 is for sale! Lots of od parts to be offered! Lane, I will bring your tranny and glass...

Well, in between work and travels, I am slowly digging into this beast. I discovered that I will have to review all work done on the frame due to some inconsistencies: missing exhaust doughnut after turbo, a few bolts in upside down, etc. It is amazing the differences between this A2 wanna be...

Welcome, In Arkron, Ohio, Sam Winer has a bunch of S250's advertised for at least a year or so for around $850. I looked at them last year and most were in good usable condition. I have a tray mount for the S250 that fits in my M1037 HMMWV...I do not know the dimensions currently but it is...

I thought I would bring this back up to the top of the heap in case someone missed it. This is going to be a good show with a lot of green iron! I am still bringing the stuff I mentioned...so save freight and buy it at Clare!

RE: Re: RE: Re: RE: Watermark - Decision FYI: On another site...for MB Unimogs, you need to be a member and you need to be signed in to see the pictures plus they watermark the picts too. In a way it is good for the posters/members, etc. but perhaps limiting for the newbie that wants to see...

Thanks for the input on CTIS! My only thought was for the truck to have the hubs setup for CTIS but not install it. Configured this way would make it more correct...I will take this offroad but not stump jumping and dune climbing (yes even here in MI there are large forests and sand dunes!)...

Yes A1 hubs and I have to decide if I want to change them out to A2 for CTIS...what everyone's opinion? George, I'll keep in touch. The alt pulley I have sets too far away from the alt which places it out of alignment from all the other pulleys/idlers. Shall investigate further...

superburban, All I can say is keep looking, asking around and don't give up. Also, when you are not looking, they fall into your lap, per se. Depending on how much money you want to spend, there are several good hmmwv's for sale, with titles. Start with David Uhrig's website armyjeeps.net...

Hi George, Thanks for the infor for you are one the guru's! IP is dated 10/03 and the engine was test fired around 2004. This is why I want to check it's operation prior to further build up. The engine currently has the 100 amp dual output alternator (need pulley) and I will have to check the...

Austin has received a lot of my cashola over the years...he has a great setup: go to site, click buy it now, click send money...lucky dog! Believe it or not, there is not as much missing as one might think (a lot of boxes)! Also, I may add AC since it is in the mid 90's again! This also came...

Currently I am sorting out all the missing components, making a nsn list, ordering/finding the parts and then assembly. I really want to get the drive train and engine compartment complete so I can fire the engine. I will keep you all posted when it is operational. Also, CARC painting is now...

That is the same kit setup I am looking at here in MI. George, thanks for taking the time to pull the kit apart for it helps me a lot with the one I am looking at! Joel, you better buy this one! BTW, I like the "Abused World Wide" tag line!

Well I did it again, I went looking for one thing and found another project...The last project was the M38 in the background and now this one is a HMMWV A2 version with 6.5 TD, 4 speed, and 242 t-case running gear. I promised my wife that this will not be a marathon assembly like the M38 but a...

Thanks emmando22...will do if I pick it up. I need to find out what is included and then go from there.