Search results

I did a search and have not seen any pics on attaching the chain type connectors to the rockwells. I have the bar and chain connectors. I am planning on towing a M715 with rockwell axles. I am using a 2013 3/4 ton dodge Cummins. The M715 has a NP205 twin sticked transfer case. So I can put...

Here are a few shots of my newly acquired M998.:mrgreen: It appears to be in real good shape and runs well. I still need to attach the pipe to the exhaust for fording. Would not mind having a winch and all necessary items for a ring mount to attach the M2HB. Leads would be appreciated, as...

Just got a m998. Looked real quick under the hood to check oil , coolant , etc.. could not find where to add /check coolant. I am sure its a dumb question , but where do you check or add ? Thanks.

I bought an alternator from OD Iron and replaced the old one on the drivers side. Gen 1 light is still on bright. What can be causing this light to stay on?

lift is for a m1028. I want new front and rear springs. No blocks.. it needs to be at least 3/4 ton because I am hauling a gooseneck.4" lift. Please post a link if possible. I have done a search. Skyjacker seems to be the priciest, is it the best? Thanks in advance.

It may just need a belt. What is the part # and manufacture for these? Where is the best place to buy an alternator should i need one ? Is the Generator 1 light , the generator on the drivers side? Thanks in advance.

Fred and i got the M37 running. I pulled off the battery cable to see if it would still run, like you would do on a 12 volt system to check alternator, M37 died. I asume its not charging. How can I check to see if the regulator or generator is not working. I know very little about electrical...

I am changing my injection pump solenoid and forgot which side to put the connector for hooking up the single pink wire on the injection pump solenoid. If you are standing in front of the front grill is it the left post or the right? The right would be close to the plunger mechanism so, I...

Lookin hard at this one. Give me maybe an average range. I know somthing is only worth what you can get out of it. http://cgi.ebay.com/ebaymotors/ws/eBayISAPI.dll?ViewItem&ih=004&sspagename=STRK%3AMEWA%3AIT&viewitem=&item=140134527599&rd=1,1

It should go pretty good. There is a locker in the front on the M1028's isnt there ?

After the truck has been started and warmed up and then you shut it off and let it sit for about 1/2 hour , it will not start unless you give it a shot of starting fluid. When the engine has set the 1/2 hour, and is still warm, the "wait" light does not come on. Anyone have any suggestions or...

This is the piece with the spline inside it used on the front rockwell 2 1/2 ton axle. I need two of them. Email me price shipped to 45056. Thanks, Chris

I am having a truck sandblasted and was going to use POR15 on the axle and frame. Now I am considering just using the 2part epoxy primer(recommended under CARC) by Sherwin Williams on the frame, axles and body. Then Painting everything CARC. My Question would be is the 2part epoxy primer just...

Bought a nice Medium tow bar, with tow bar ends and tow straps (the ones with the double chains).Had all the correct pins with lanyards. Paid $300. Best of all no shipping. This thing is heavy. Was this a fair price on this ? :?:

I am installing a locker in the front. I havent figured out how to remove the axles. Please lmk how you do this? :?: I have taken wheel, hub, and bearing nut OFF. The back axles and locker went pretty good. Thanks Chris

I am going to have wheels made by stazworks for an m715 with rockwells. I would like to have them to be interchangeable with my deuce, should I go with the singles on it. Optimum for the M715 will be 10 x20 with a 6" backspacing. Will this size fit the deuce without problem? Thanks Chris

These are the various plates used to hold the springs on the front axle. I do not need the ubolts. I need another set like what you see. If you have some LMK what you want for them or if you know where I can get some LMK.

I have a whistler turbo off of a Hercules will this bolt to a LDT465 manifold ? will it work on anything else? Thanks Chris

A local guy has some Rockwells on a non-running deuce in my area. I need to know if they are the "U-joint" type. I tried to fill behind the rubber boot, But could not get my hand behind what seems to be a flange on the end of the axle tube.. It is in a 1970 model. The data tag says Rockwell...

I want the ones with the U-joint in the front axle. I need one front and one rear. I have M715 stuff to trade or cash. email: elohimfirst@msn.com Phone: 513-523-4918