Search results

I just found a 20"x9" wheel. It is one piece, tubeless and steel. I have seen some on the M105's that were 22.5. Any thoughts on what they were for? I wish I could find a set.

Does anybody have drawings/blueprints for the deuce wheel. I am lookinmg for the stock wheel, but anything would help. I am on a mission!

I just won an auction for 5 new 1100r20 tires for my bobbed deuce. Can I reuse the 900x20 bias flaps with the new tires (same stock wheels)? I think I am going to get the wheels refinished at the same time $22 each. The tubes are also $22.

Is the distance between the towing clevises on the Deuce and 5 ton the same? Does it vary?

Does anybody have a good source for a pair of 1" towbar feet? I placed a classified for them but no reply.

Does anybody know anything about an M38 with 11.00-20 tires and wheels that was tested? It was nick named Hi Helen. Any photos?

A while back monster man & Joe Young made a heater instalation manual with a bunch of photos. It's still listed on the resources page but none of the photos come up. Can anyone help? I am also looking to make air intake scoop. Do anyone have the mesurements? Westfolk just sent me a link for NOS...

I have a 24v-12v coverter. It is rated for 10 amps. Could that be hooked up to a 12v battery like a charger giving me a 12v system that would allow me to run larger loads than 10amps for short periods of time? Would it over charge the battery or taper down like a battery charger?

Does anyone know anything about an M38 with 1100-20 tires and a cut down body. Fred Chrimson has a couple of photos in his book. It may have only been tested. They refered to it as "Hi Helen".

How cool is this? Sometimes just the little things make you happy.

I just came across German Army issue antenna for the SEM-25 radios. The discription said they work from 25mhz - 70mhz. They have a tuning box with them but there is also a remote unit that tunes the antenna which isn't incluided. I would like to use this with a CB set, 27mhz. The antenna needs...

I just won an M101 trailer that I need to pick up next week. Does anyone know the ID of the lunette ring. I may use a ball hitch adapter to tow it home. I couldn't find a manual for it only the newer m101a series trailer, is it there?

I just won an M101. I've checked for a manual on the site and only found the newer m101a manual. Am I missing it? Does anyone have the electronic version that they can post or send to me? I may want to sell my WW2 Converto trailer, needs restoration, now.

I lost my drain plug (bottom) from my axle. Not while driving, while doing a lube change. I am sure I will find it as soon as I buy one. Anyone know what size it is I think it is 3/4" pipe thread. Gasket? Material? I know I could pull the other one but I am leaving on a trip in a couple of days...

I am a little out of place here. I just got a CJ7, haven't even picked it up yet. Does any one know if there are any free manuals on line. If I had found a military one I would know right where to look. I know she has some frame problems. If anyone has parts or even a frame let me know.

I just bought some new toys. One of the things was a trailer dolly. It is a tandem axle commerical rig, 8 tires, Dayton rims. I can't decide if I should keep it to go with the Deuce or sell it. I have a good set of NDTs I could put on it. I need to pick it up soon and will take some pictures then.

I have the rear axle apart to change over to singles. I ordered new seals and brake cylinder kits to be replaced at the same time. Nothing is leaking, I just thought it would be easier just to break it down once. The cylinder bores look good and shiney. Should I just clean it up and replace the...

The compressor wrenches are finished and the first one went out today. See the classifieds. Would anyone be interested in a Fuel Injector Pump wrench? This is the spanner that is used on the IP hub.

I need to replace the two universals on the drive shaft between the transfer and the front-rear axle (Middle). I have looked at the parts TM's and can't figure out which ones I need. Some of the drawings show a carrier bearing, mine doesn't have that. Also my universals have clips not flange...

Did someone here have DOT 5 for sale?