-
Steel Soldiers now has a few new forums, read more about it at: New Munitions Forums!
Search results
-
-
LMTV Air Conditioner AC Main Unit Gen1 and Gen2 Details
No, there is not 24 volts fed to the high pressure switch but if the ground circuit is open you will measure 24 volts there. It controls the fan relay which turns the fan on. It is grounded through the fording switch. -
3053 Transmission
That is what it was designed for but there was likely at least a 100% safety factor- m-35tom
- Post #4
- Forum: Deuce Modification and Hot-Rodding
-
Mep-1050, mep-1051, 4-1050, 4-1051
been a long time, probably gone.- m-35tom
- Post #19
- Forum: Generators
-
M1078 LMTV planetary hub setup
as bearings wear and need adjusting the gear lash needs adjusting. plus if it was ever done by the army it is wrong. -
M1078 LMTV planetary hub setup
Does not matter how you do it results will be the same. It is very easy to do. -
Gen 2 air conditioning install with C7 A1R - notes and pictures thus far.
the lower bracket does go behind the upper, never had a fit issue. -
LMTV Air Conditioner
I know several people who have used the 1st gen and been happy. Key to good cooling is insulating the cab. A study by NIS showed that the 2nd gen was 16K btu. I have not found info on the 1st gen but would not believe Red Dot specs -
MEP-802/803 fuel return improvements
no need to take anything else off it is very easy to get to. replace all the hose, the short sections are just as likely to leak.- m-35tom
- Post #111
- Forum: Generators
-
FMTV High Speed Gears
You will save the most by just getting the ring & pinion, easy to install by any good mechanic. $875 each set includes shipping. -
Air conditioner install using Waterloo parts
2 pin orange and black is 24v power from PDP. 4 pin goes to the original power connector the heater used. -
-
LMTV M1078 Transmission oil confusion...please help!
The truck has to be running to check the fluid. One level is automatically set and the other is by dipstick. -
LDS bellhousing into a deuce? Mounts?
Just swap the flywheel housing from the LDT, it is by far the easiest way. And also swap the oil pan and pickup parts. You are not gonna find a 6 speed that is short enough to swap in without major relocation of transfer case.- m-35tom
- Post #4
- Forum: Deuce Modification and Hot-Rodding
-
Power Steering Possibility?
Take the fender off, box installation and pump installation then is pretty easy.- m-35tom
- Post #155
- Forum: Deuce Modification and Hot-Rodding
-
Caiman MRAP wheels on a LMTV
Has nothing to do with tires, the wheels have 3/8" runout!! -
Caiman MRAP wheels on a LMTV
It is not about weight, it is about balancing. All the steel wheels I have seen have about 3/8" runout on the inside flange. Impossible to balance. -
Caiman MRAP wheels on a LMTV
I have heard / read that the Caiman MRAP aluminum wheels will work on a LMTV. I am skeptical since the LMTV is lug centric and the MRAP is hub centric. Has anyone successfully done this? -
5ton to m35 power steering upgrade
Still a few kits available, these are the last to ever be made. https://www.waterloospecialties.com/steering/index.html- m-35tom
- Post #40
- Forum: Deuce Modification and Hot-Rodding
-
LMTV Air Conditioner
I have 20 compressor mounting kits on the way, also plenty of evaporator units and plenty of condenser units, wiring, hose fittings, etc https://www.lmtvtrucks.com/