Salty dog
Active member
- 112
- 175
- 43
- Location
- Spring, Texas
Was going over a HMMWV that I recently bought and noticed the line from the Cadillac valve has been bypassed, any ideas why this was done?
-
Steel Soldiers now has a few new forums, read more about it at: New Munitions Forums!
Cadillac valve
- Thread starter Salty dog
- Start date
- 6,931
- 9,589
- 113
- Location
- Papalote, TX
Looks like it is blocked, your fan should be running 24/7, maybe a mongo leak between the fan shroud and the clutch?
Salty dog
Active member
- 112
- 175
- 43
- Location
- Spring, Texas
The fan spins as soon as the motor is started,
- 6,931
- 9,589
- 113
- Location
- Papalote, TX
Well they all do that, if you rev the motor when the fan is engaged it is usually pretty obvious by the noise it makes.
Heck hook it up and see what happens
- 1,710
- 2,265
- 113
- Location
- Rosamond, CA
AHAaaa, Try it with compressed air and rubber tipped air/blow gun into the fan clutch fitting. Check for operation and listen for leak. Engine off. Easier to clean up air than oil.
MR. CLEAN, CAMO
MR. CLEAN, CAMO
Last edited:
- 6,931
- 9,589
- 113
- Location
- Papalote, TX
I did not divulge I have stock in the Zip-Zorb industry
- 1,710
- 2,265
- 113
- Location
- Rosamond, CA
You mean 'KITTY LITTER" lolI did not divulge I have stock in the Zip-Zorb industry
Now I got a GO, CAMO
- 6,931
- 9,589
- 113
- Location
- Papalote, TX
Pam (wife, 45 years)
used to work as an operator at a VCM chemical plant, that is what they called it, so just like "zippy ties" it is now part of our vernacular
Salty dog
Active member
- 112
- 175
- 43
- Location
- Spring, Texas
I appreciate all the help, I have been trying to go through the TM for a reference to see how the hose is routed. I took a look under the fan shroud and do not see anything connected to the fan clutch. I did see this attachment point on the back of the radiator but unsure its purpose
Attachments
- 6,931
- 9,589
- 113
- Location
- Papalote, TX
That is where the hose goes.
The hose that goes from the other side of the fitting to the fan clutch may be missing, that could be why it was plugged, that hose is a PITA to replace.
OR the hose may just be laying in the bottom of the fan shroud not connected.
The hose that goes from the other side of the fitting to the fan clutch may be missing, that could be why it was plugged, that hose is a PITA to replace.
OR the hose may just be laying in the bottom of the fan shroud not connected.
Last edited:
- 6,931
- 9,589
- 113
- Location
- Papalote, TX
I am going to go out on a limb here and say that possibly the quick connector was leaking and someone thought unplugging it would stop the leak, when it did not they pulled and plugged the hose.
If you find the hose just laying there it might be a good idea to order one of the female connectors, seems they all leak sooner or later.
If you find the hose just laying there it might be a good idea to order one of the female connectors, seems they all leak sooner or later.
Salty dog
Active member
- 112
- 175
- 43
- Location
- Spring, Texas
Does the radiator need to be removed to install the hose that connects to the fan clutch?
- 6,931
- 9,589
- 113
- Location
- Papalote, TX
No need to remove the hose to replace the quick connector
- 6,931
- 9,589
- 113
- Location
- Papalote, TX
I was wrong, the nut is on the inside(#20), I thought it was on the outside, getting old
Maybe someone has done it but it looks next to impossible without removing the radiator.
If that fitting had the nut on the outside it would be possible to fish it to the hole and put the nut on it..
Maybe someone has done it but it looks next to impossible without removing the radiator.
If that fitting had the nut on the outside it would be possible to fish it to the hole and put the nut on it..
- 711
- 982
- 93
- Location
- Southern Minnesota
When I had the radiator stack out I replaced mine with a quick connect. It could be done without, but it takes someone with small hands and/or a contortionist.
Salty dog
Active member
- 112
- 175
- 43
- Location
- Spring, Texas
Crawled underneath the HMMWV today and confirmed there is no hose assembly in the fan shroud area