• Steel Soldiers now has a few new forums, read more about it at: New Munitions Forums!

  • Microsoft MSN, Live, Hotmail, Outlook email users may not be receiving emails. We are working to resolve this issue. Please add support@steelsoldiers.com to your trusted contacts.

Crank, no start, white smoke.

erasedhammer

erasedhammer

Active member
843
61
28
Location
Maryland
cucvrus said:
Loosen the flare nut on the fuel lift pump and see if it has any fuel pumping when you crank it over. is the fuel pump dry externally?
Click to expand...
Yes the pump is dry. But that pump is working. There is fuel getting to the inlet of the filter. I'm probably overthinking this and its just a clogged filter. Hopefully.
 
Barrman

Barrman

Well-known member
5,276
1,798
113
Location
Giddings, Texas
I had the same thing on my M715 with a 6.2 last week. Fired it up, it ran for a minute or so and then died. No restart. I changed out the 3 year old filter, bled it and it fired on the 3rd try.

Start simple on these engines. Battery grunt to turn a good starter. Air into the engine and a steady fuel supply to the IP. After that is IP health and compression.
 
erasedhammer

erasedhammer

Active member
843
61
28
Location
Maryland
Barrman said:
Put a magnet up the slot the push rod lives in. There is no place for it to go but out of the fuel pump mount location.
Click to expand...
Yeah I'm having trouble finding a magnet that is small enough. Most are large ones used for picking up bolts.

Where can I get a new rod? It doesn't look like napa/O'Reilly/AutoZone has one ...
What grease do I use for the new rod?

Update: got a magnet, got the piece out. Good to go there.
got some all purpose grey grease. Should work well.
 
Last edited:
cucvrus

cucvrus

Well-known member
11,474
10,441
113
Location
Jonestown Pennsylvania
I guess you are in a hurry for one. I have a few in scrap engines. PM me an address. Wheel bearing grease will hold it up in there till you install the pump. Put a new pump on while you are in there. Good Luck.
 
erasedhammer

erasedhammer

Active member
843
61
28
Location
Maryland
I guess this push rod is a little difficult to get. Amazon doesn't have any?

I'm in a hurry to encounter the next problem that will keep this engine from running.
 
Last edited:
doghead

doghead

4 Star General /Moderator
Staff member
Super Moderator
Steel Soldiers Supporter
26,246
1,179
113
Location
NY
They can be found on ebay for around $5 often.

The hole is a vent, I believe.
 
cucvrus

cucvrus

Well-known member
11,474
10,441
113
Location
Jonestown Pennsylvania
FrankenCub said:
All my years working on Chevy engines and this is the first I've seen one of these break :shock:
Click to expand...
Same here. I never seen any break except on line. Not sure if it involves some operator error on fuel pump installation. But I never seen or heard of them broken before the internet came along. And I can't find one for giving away at the moment. I would need to go out and remove a fuel pump from a parts truck. Good Luck Have a Great Day.
 
cucvrus

cucvrus

Well-known member
11,474
10,441
113
Location
Jonestown Pennsylvania
319cssb said:
Most i saw have been installed wrong.
Click to expand...
How can you install it wrong? Please? I have installed them a thousand times. Maybe I am doing it wrong. My cobbler bench was Round peg, Round hole, Square peg, Square hole, See my point? It only fits one way and each end is the same. If you know something here enlighten me. Please. :)
 
You must log in or register to reply here.
111,206members
165,494threads
2,328,917posts
1,379online users
Top
✖
AdBlock Detected

We get it, advertisements are annoying!

Sure, ad-blocking software does a great job at blocking ads, but it also blocks useful features of our website like our supporting vendors. Their ads help keep Steel Soldiers going. Please consider disabling your ad blockers for the site. Thanks!

I've Disabled AdBlock
No Thanks