- 2,136
- 613
- 113
- Location
- Davis County, UT
Several questions here as I can't seem to find the answer in the TM and/or don't know the right words to search for on the forum...
1. Why is there grease on the INSIDE of the drum assembly?
![2015-03-14 19.57.43.jpg 2015-03-14 19.57.43.jpg](https://www.steelsoldiers.com/data/attachments/373/373541-ec8e1b4481687d4db5e1e02055564ff3.jpg)
2. Similar to #1, why was there grease on the spindle (the yellow)? I can't ascertain as to WHAT they were greasing (just catching dust?), and with the previous army mechanic's finger marks in the grease still visible, it couldn't have actually been touching anything...
![2015-02-25 19.28.32.jpg 2015-02-25 19.28.32.jpg](https://www.steelsoldiers.com/data/attachments/371/371158-9976b12a66b80feddfb6ba74e72f9af8.jpg)
This TM says to remove the grease from the spindle (step 3):
![spindle_replacement.jpg spindle_replacement.jpg](https://www.steelsoldiers.com/data/attachments/373/373542-daf05dc749e2e235bf1bfe951ecc82a4.jpg)
3. I purchased a seal & boot kit similar to (just without the gaskets)
http://www.bigmikesmotorpool.com/co...et-and-seal-kit-w-gold-zipper-boots-for-m35a2
I've replaced the inner-axle oil seal (the one that separates the U-joint from the axle tube):
![2015-03-07 14.48.12.jpg 2015-03-07 14.48.12.jpg](https://www.steelsoldiers.com/data/attachments/372/372646-181d868dbf49793132271701d6b5ef0d.jpg)
I've replaced this seal for the inner bearing,
![2015-03-07 18.55.19.jpg 2015-03-07 18.55.19.jpg](https://www.steelsoldiers.com/data/attachments/372/372655-9c609ea0bda8d3074b52c18b5695f2ad.jpg)
But where does the "third" seal go?
I obviously don't understand the terminology here as I don't see the TM talking about it (I'm reading in the Maintenance TM, part 2, "TM9-2320-209-20-3-2"), and I can't find pictures for it both here and numerous other folk's threads.
Thanks!
1. Why is there grease on the INSIDE of the drum assembly?
![2015-03-14 19.57.43.jpg 2015-03-14 19.57.43.jpg](https://www.steelsoldiers.com/data/attachments/373/373541-ec8e1b4481687d4db5e1e02055564ff3.jpg)
2. Similar to #1, why was there grease on the spindle (the yellow)? I can't ascertain as to WHAT they were greasing (just catching dust?), and with the previous army mechanic's finger marks in the grease still visible, it couldn't have actually been touching anything...
![2015-02-25 19.28.32.jpg 2015-02-25 19.28.32.jpg](https://www.steelsoldiers.com/data/attachments/371/371158-9976b12a66b80feddfb6ba74e72f9af8.jpg)
This TM says to remove the grease from the spindle (step 3):
![spindle_replacement.jpg spindle_replacement.jpg](https://www.steelsoldiers.com/data/attachments/373/373542-daf05dc749e2e235bf1bfe951ecc82a4.jpg)
3. I purchased a seal & boot kit similar to (just without the gaskets)
http://www.bigmikesmotorpool.com/co...et-and-seal-kit-w-gold-zipper-boots-for-m35a2
I've replaced the inner-axle oil seal (the one that separates the U-joint from the axle tube):
![2015-03-07 14.48.12.jpg 2015-03-07 14.48.12.jpg](https://www.steelsoldiers.com/data/attachments/372/372646-181d868dbf49793132271701d6b5ef0d.jpg)
I've replaced this seal for the inner bearing,
![2015-03-07 18.55.19.jpg 2015-03-07 18.55.19.jpg](https://www.steelsoldiers.com/data/attachments/372/372655-9c609ea0bda8d3074b52c18b5695f2ad.jpg)
But where does the "third" seal go?
I obviously don't understand the terminology here as I don't see the TM talking about it (I'm reading in the Maintenance TM, part 2, "TM9-2320-209-20-3-2"), and I can't find pictures for it both here and numerous other folk's threads.
Thanks!
Last edited: