- 1,998
- 31
- 48
I was doing the front and rear axle PMs on the daughters M1008 and when I got to the front axle, found this!
Anyone have an idea where to get a new cover?
Anyone have an idea where to get a new cover?
-
Steel Soldiers now has a few new forums, read more about it at: New Munitions Forums!
Front Diff Cover
- Thread starter 4x4 Forever
- Start date
- 9,604
- 1,493
- 113
- Location
- mid- michigan
Auto parts store.
- 1,998
- 31
- 48
Napa , Hi Price/Low Quality, Advanced don't have it...any OTHER ideas?
No longer available from GM either...
No longer available from GM either...
Last edited:
- 9,604
- 1,493
- 113
- Location
- mid- michigan
www.currieenterprises.com Part #: 60-1005
Our Price: $52.95
or do a google search for dana 60 front cover .
Our Price: $52.95
or do a google search for dana 60 front cover .
Last edited:
- 1,998
- 31
- 48
Did a search but all I found was the 238$$ Magnalight jobbies...Thanks!!
CA_LEO
Member
- 64
- 5
- 8
- Location
- Grass Valley, CA
http://www.ruffstuffspecialties.com...roduct_Code=D6070COV&Category_Code=diffcovers
Still a little pricey, but I have heard, stress heard, this guy makes really nice diff covers. Some of my buddies have jeeps with his diff covers on them.
Still a little pricey, but I have heard, stress heard, this guy makes really nice diff covers. Some of my buddies have jeeps with his diff covers on them.
Cucvnut
Well-known member
- 3,804
- 61
- 48
- Location
- Carver, Oregon
WFO, ORD, 4 wheel parts great lakes off road, ruff sruff, Diy4x
466Navastar
Member
- 199
- 0
- 16
- Location
- Buffalo,ny
what am i missing here?.....remove the bolt and braze or weld the hole shut
where did the bolt come from...ring gear?
where did the bolt come from...ring gear?
Last edited:
richingalveston
Well-known member
- 1,715
- 120
- 63
- Location
- galveston/Texas
patching the hole is easy. figuring out where the bolt came from and what else is missing or broken in the diff would be my biggest concern. The bolt came from the inside of the diff. so something has to be wrong, unless it was a previous failure and they left the bolt there to keep the hole plug. If that was the case then it was a bad idea.
Skinny
Well-known member
- 2,130
- 488
- 83
- Location
- Portsmouth, NH
Assuming that everything in the front end is OK, that would take a metal fabricator a whopping 5 minutes to fix. It will take him longer to get his tools out than to fix that.
If you decide to go with a replacement cover, pretty much everyone makes a decent cover these days. Seems like the cast ones are cheapest and typically have a drain and fill hole.
If you decide to go with a replacement cover, pretty much everyone makes a decent cover these days. Seems like the cast ones are cheapest and typically have a drain and fill hole.
- 1,998
- 31
- 48
Thanks for all the replies guys. Looks like it came from the ring gear.
Also looks like it rattled around one time too many...
Also looks like it rattled around one time too many...
M1008driver
New member
- 522
- 3
- 0
- Location
- Great Falls, Montana
Last edited:
- 1,500
- 1,678
- 113
- Location
- Puget Sound, WA
Have someone weld the bolt down so it doesn't move. Clean the cover out really well, then write what you know of the story of the bolt on the inside of the cover with a Marsh white marker. Someday another owner may find it and it'll be a cool surprise.
We used to use those markers to write long stories on the inside of jet engines during rebuild. I still have a drawer full of those markers- good stuff.
We used to use those markers to write long stories on the inside of jet engines during rebuild. I still have a drawer full of those markers- good stuff.
- 1,998
- 31
- 48
M1008, that is what I WOULD like, but will not spend big money for a cover.
Mainsail, that would be so NOT cool, and is not going to happen, it will be fixed the right way, the first time.
Mainsail, that would be so NOT cool, and is not going to happen, it will be fixed the right way, the first time.
Vhyle
New member
- 181
- 1
- 0
- Location
- Clarksville, TN
Wow, that's strange. My money is on someone used it to plug a hole before.
- 1,998
- 31
- 48
12345678910
CA_LEO
Member
- 64
- 5
- 8
- Location
- Grass Valley, CA
Just stumbled across this here:
http://www.saturnsurplus.com/cucv/cucv.htm
Seventh one down on the list.
http://www.saturnsurplus.com/cucv/cucv.htm
Seventh one down on the list.
Skinny
Well-known member
- 2,130
- 488
- 83
- Location
- Portsmouth, NH
The covers are expensive but the nice feature is the drain/fill plugs that they usually come with. I don't know about you but I absolutely despise dropping a pan or cover that doesn't have a drain hole. We have the technology...it makes life easier. Plus you can set that thing in with RTV and forget about it. Changing fluid doesn't have to be a messy process along with scraping the gasket surfaces. You only have to pull two plugs out to do the whole thing. If I was in your situation and had to replace the cover (if you decided not to weld it), I would get a cover with drain/fill plugs. Just my two cents.