Help! I installed a new set of glow plugs and started right up at 24 degrees. A few days later 48 degrees and took forever to start with a nice white smoke show lol! My glow plug light comes on as it should (no flashing). When I pull a boot from one of the glow plugs and test it, it has 24v and never tapers down like it should. Is this a smart box issue, GPC issue, voltage regulator issue or something else?? TIA!!
-
Steel Soldiers now has a few new forums, read more about it at: New Munitions Forums!
Glow plugs roasted
- Thread starter softail97
- Start date
- 7,015
- 9,692
- 113
- Location
- Papalote, TX
Welcome to the SS forums!!
- 3,003
- 4,419
- 113
- Location
- Olympia/WA
It is NOT a voltage regulator issue. Completely separate system.
Usually a smart box issue.
GPC just tells the smart box if the engine is warm enough to need glow plugs or not, but doesn't have any direct control over them.
Usually a smart box issue.
GPC just tells the smart box if the engine is warm enough to need glow plugs or not, but doesn't have any direct control over them.
- 198
- 276
- 63
- Location
- Flagstaff, Az
"My glow plug light comes on as it should (no flashing)."
Does the light ever go out, or stay on permanently?
Does the light ever go out, or stay on permanently?
Thx I was afraid of that
yes the light goes out some where around 6 second.
M1165A1
Well-known member
- 423
- 873
- 93
- Location
- The High Country, CO
What glow plugs did you use? The proper ones, or the Chinese ones?
Also: get a glow plug removal tool. Chances are one or several of your plugs are swelled up and won't removed easily.
blackdogcustoms.com
Also: get a glow plug removal tool. Chances are one or several of your plugs are swelled up and won't removed easily.
HMMWV® Glow Plug Extractor Kit w/ Glow Plugs - Black Dog Customs
HMMWV® Glow Plug Extractor Tool with Glow Plug Kit This is the best extraction tool on the market and is a MUST have for anyone that owns an HMMWV®/humvee®. Swollen glow plugs are near impossible to remove. With our tool, you simply unscrew the center part of the tool place it around the plug...
blackdogcustoms.com
Last edited:
I bought them from black dog customs.What glow plugs did you use? The proper ones, or the Chinese ones?
Also: get a glow plug removal tool. Chances are one or several of your plugs are swelled up and won't removed easily.
HMMWV® Glow Plug Extractor Kit w/ Glow Plugs - Black Dog Customs
HMMWV® Glow Plug Extractor Tool with Glow Plug Kit This is the best extraction tool on the market and is a MUST have for anyone that owns an HMMWV®/humvee®. Swollen glow plugs are near impossible to remove. With our tool, you simply unscrew the center part of the tool place it around the plug...
thompsoncustom
Active member
- 136
- 106
- 43
- Location
- iowa
when my smart box died it did the same thing. Light worked as it should but the glow plug had a constant 24v that fried them all. I modified my smart box to make it a manual controller that way it never happens again and the cost was around $100 bucks.
if you go that route this will help alot
How to bypass PCB? I am aware some HMMWV owners have done it. TOBASH | SteelSoldiers
if you go that route this will help alot
How to bypass PCB? I am aware some HMMWV owners have done it. TOBASH | SteelSoldiers
Last edited:
M1165A1
Well-known member
- 423
- 873
- 93
- Location
- The High Country, CO
Those are the good ones, so you can rule out cheap glow plugs. Signs point to start box.
If you decide to replace it, get the Camotek.
Home
Camoteksystems brings you the HMMWV start box power distribution manual glow control...PDMGC!
www.camoteksystems.com
thx for the info!!
- 1,512
- 1,696
- 113
- Location
- Puget Sound, WA
The question should be, what size wrench did you use to install them? If it was 10mm, they're cheap junk. If 3/8" then they're probably OEM.Those are the good ones, so you can rule out cheap glow plugs. Signs point to start box.
If you decide to replace it, get the Camotek.
Home
Camoteksystems brings you the HMMWV start box power distribution manual glow control...PDMGC!
M1165A1
Well-known member
- 423
- 873
- 93
- Location
- The High Country, CO
Black Dog only sells the proper Wellman ones, so that's how you know without measuring. Had he said "certain other vendor" who I shall not name, I'd say that was the issue.
- 3,596
- 3,518
- 113
- Location
- Brooklyn, NY
Rebuild your box. My signature line contains the instructions. It will be much more robust afterwards.
