fpchief
Well-known member
- 1,041
- 220
- 63
- Location
- South Alabama
Looks like they hammered it trying to destroy the valve while still installed....
-
Steel Soldiers now has a few new forums, read more about it at: New Munitions Forums!
Help : what is missing?
- Thread starter DefendersMN
- Start date
DefendersMN
New member
- 15
- 9
- 3
- Location
- ROCHESTER MN
Ya I think it is. I went ahead and got a ful DWF kit because so much is gone, the switch, the intake stack, the exhaust, etc
Sent from my iPhone using Tapatalk
DefendersMN
New member
- 15
- 9
- 3
- Location
- ROCHESTER MN
You mean all the hoses? Not many miles(28?!?) on it but I realize it has been sitting in the desert for 10+ years
Sent from my iPhone using Tapatalk
DREDnot
Well-known member
- 723
- 443
- 63
- Location
- Phoenix, AZ
This thread has inspired me to pick up some NOS hoses before the rush...
Attachments
fpchief
Well-known member
- 1,041
- 220
- 63
- Location
- South Alabama
Probably was a good idea. You most likely will not have to take off breather, I doubt they messed with the kit that goes on the bottom of it.
- 5,605
- 2,898
- 113
- Location
- Metairie/La (N'awlins)
those hoses are hard to get to, much easier with valve off.
Let me guess, M1123 from Barstow? I just noticed this exact same thing on my hmmwv. They shoved a
‘gap’ hose from one hose to the other. They destroyed one of the hoses when doing this. I just ordered a CDR (not the fording one) and two new hoses.
I’m curious if this will effect blow by in any way. Did anyone here experience a reduced blow by when adding / fixing / replacing the CDR?
‘gap’ hose from one hose to the other. They destroyed one of the hoses when doing this. I just ordered a CDR (not the fording one) and two new hoses.
I’m curious if this will effect blow by in any way. Did anyone here experience a reduced blow by when adding / fixing / replacing the CDR?
I have the 1123 also, missing the cdr and switch. Mine will not shift up or down, checked for vacuum leak by spraying starter fluid on lines, no change in idle, fluid is clean and full, any help is greatly appreciated?!
diesel_dave
Well-known member
- 212
- 285
- 63
- Location
- Utah
This is a diesel engine so there really isn't any vacuum. None of those tubes have anything to do with the transmission shifting issue you are having.
Thank you,, Any idea of what it would be?
diesel_dave
Well-known member
- 212
- 285
- 63
- Location
- Utah
You have a 4L80e where the "e" stands for electronic. Which means the transmission is electronically controlled. That being said, there are about a dozen basic things that could cause what you describe. Is your truck stuck in first gear or is it in second? If it's in second, it's probably in limp mode.
Seems like over drive, take off is a little sluggish then gets upto speed and when I let off the gas and apply gas again it revs up to catch up where it left off.
diesel_dave
Well-known member
- 212
- 285
- 63
- Location
- Utah
It's stuck in fourth gear? That would be unusual.
2nd or 3rd., I even started out in1st and manually shifted and had no reaction, could not feel a shift up ou down?
- 6,862
- 9,503
- 113
- Location
- Papalote, TX
ALSO for you guys with no CDR valve, that hose in the middle of the bracket goes DIRECTLY into the intake, one small screw, washer etc. and your engine is TOAST, do not pass go do not collect $200 it's time for a new engine!!!!!!
PLUG THAT HOLE!!!!!!
PLUG THAT HOLE!!!!!!
blutow
Well-known member
- 357
- 501
- 63
- Location
- Austin, TX
It sounds like it's in limp mode (which means fixed in 2nd gear). This document (link below) has some really good info about how the transmission works and how to troubleshoot it. I'd start by checking the breaker behind the passenger seat. The transmissions is all electronic and the brain is in the box behind the drivers seat. Lack of electical power can cause limp mode (check breaker) or it could be any number of other faults. I'd also check the connection to the transmission box and transmission. Disconnect the negative on the main battery before disconnecting or reconnecting the TCM harness.
- 6,862
- 9,503
- 113
- Location
- Papalote, TX
Actually the 4L is not all electronic, it is a half breed/messed over regurgitated TH400,,the 6L was GM's first all electronic transmission
Thank you for the help!