74M35A2
Well-known member
- 4,145
- 330
- 83
- Location
- Livonia, MI
Dropped off some scrap at the metal yard, saw a pile of these. Is the differential to something large with indepedent suspension. Mil colored.
-
Steel Soldiers now has a few new forums, read more about it at: New Munitions Forums!
Interesting Find
- Thread starter 74M35A2
- Start date
- 1,330
- 586
- 113
- Location
- Quantico VA
Mrap?
- 6,986
- 2,523
- 113
- Location
- Montevideo/Uruguay
Are those going to be scrapped entirely? Or would they let you pull parts off of it? I see some I could use...
- 9,604
- 1,493
- 113
- Location
- mid- michigan
Most scrapyards here in michigan don't sell parts , the state has a whole bunch of different licenses they have to get for parts. Some recyclers sell parts , mostly because they don't want to deal with the sale tax.Are those going to be scrapped entirely? Or would they let you pull parts off of it? I see some I could use...
- 6,426
- 4,985
- 113
- Location
- Ft. Lauderdale, Florida
Thanks that is some heavy duty stuff for sure.
I sure you have perked up interest. Expect PM's?
74M35A2
Well-known member
- 4,145
- 330
- 83
- Location
- Livonia, MI
I could buy all if wanted. No PM’s yet.
No idea if MRAP, I would think MRAP is old by now and they are onto the next thing? Doesn’t MRAP use solid axles? I really only know M92xA2 stuff.
I can’t run around and do quotes/weight/measurements, I’d venture to say you need to be prepared to spend about $500 minimum per. I’m not going to pull parts. All or none, but will grab one if somebody is serious.
No idea if MRAP, I would think MRAP is old by now and they are onto the next thing? Doesn’t MRAP use solid axles? I really only know M92xA2 stuff.
I can’t run around and do quotes/weight/measurements, I’d venture to say you need to be prepared to spend about $500 minimum per. I’m not going to pull parts. All or none, but will grab one if somebody is serious.
Last edited:
dmetalmiki
Well-known member
- 5,523
- 2,028
- 113
- Location
- London England
Thing is with assemblies in a scrap yard, they might well be damaged, unserviceable or just plain broken. Then again maybe not...but that is the gamble.
- 2,308
- 893
- 113
- Location
- Fargo ND
That sure as heck looks MRAP to me, since its here in the US there is a good chance its off a BRAND NEW truck!!!!
Karl
Karl
74M35A2
Well-known member
- 4,145
- 330
- 83
- Location
- Livonia, MI
More info on this. They are Arvin Meritor units, from an assembler such as AM General but not AM General. I am not going to spill beans on who dumped them. They have air locking diffs, and axle disconnect solenoids on them. They are brand new, zero damage, spin freely, and backlash feels like a new diff would, just a slight click each way. They weigh 1250lbs each, and they have 14 of them. There were a few strut assemblies also, these were massive. The coil diameter was just enormous, length also.
MRAP axles on eBay look solid, unless these are the front? No idea. There is no through-shaft on them for additional axle drive, they are dead ended.
MRAP axles on eBay look solid, unless these are the front? No idea. There is no through-shaft on them for additional axle drive, they are dead ended.
Last edited:
74M35A2
Well-known member
- 4,145
- 330
- 83
- Location
- Livonia, MI
Looks like it. This artical references Humvee, but NFW on the size of these ones.
https://www.defencetalk.com/oshkosh...ion-system-enhances-hmmwv-capabilities-29030/
Standard frame rail spacing mount pad, but these are probably worthless in the civilian world. Too bad. Locker and disco are awesome.
Last edited:
- 6,426
- 4,985
- 113
- Location
- Ft. Lauderdale, Florida
So, the people that know how how they were built,
have people that know how to make them useless.
Golly, I would like to talk to the people.
have people that know how to make them useless.
Golly, I would like to talk to the people.