seano11
Active member
- 878
- 103
- 43
- Location
- Edmonton Canada
I'm looking for some detailed pics of how the cable feeds through the level wind and then how it mounts to the winch. Thanks in advance
-
Steel Soldiers now has a few new forums, read more about it at: New Munitions Forums!
Looking for detailed pictures of level wind
- Thread starter seano11
- Start date
- 12,195
- 325
- 0
- Location
- gainesville, ga.
The cable feeds under the big roller, up through the tensioner, up over the level wind to the backside of drum.
The cable is held to the drum by 2 set screws, all this can be found in the -20
The cable is held to the drum by 2 set screws, all this can be found in the -20
mdmorgan
AM3 U.S. Navy
- 1,085
- 102
- 63
- Location
- Forsyth, Ga.
If you don't get any pics by tonight I'll take some tonight when I get off work.
seano11
Active member
- 878
- 103
- 43
- Location
- Edmonton Canada
Cool thank you
mdmorgan
AM3 U.S. Navy
- 1,085
- 102
- 63
- Location
- Forsyth, Ga.
Hope this is what you were looking for.
Attachments
- 1,093
- 146
- 63
- Location
- Los Angeles,Ca
Does the cable have to taken off the drum completely in order to run it through the level wind?
- 12,195
- 325
- 0
- Location
- gainesville, ga.
yes if you do not want to cut/remove the chain clevis, which I would do before I pulled ALL the cable
mdmorgan
AM3 U.S. Navy
- 1,085
- 102
- 63
- Location
- Forsyth, Ga.
To get it through the level wind, no. You can pull the bolts holding the cover thing off and lay the cable on the big pulley then put the cover back on. But to get it through the tensioner, yes unspool the cable or cut it like Ron said. If the cable needs grease anyway I would unspool it.
seano11
Active member
- 878
- 103
- 43
- Location
- Edmonton Canada
Thank you for the pictures it looks pretty straight forward looks like the level wind does a really good job at spooling it
Proper winch cable has one strand of rope weaved into the steel to act as a wick. Luberication is accomplished by pouring motor oil over it with an absorbant pad on the ground to catch the run off. Chassis grease is not recommended as it attracts dirt and sand to adhere to the cable and damage it.
seano11
Active member
- 878
- 103
- 43
- Location
- Edmonton Canada
Well got my level wind in tonight kinda upset about the condition tho. From what I was told it was a complete level wind set up in perfect shape. Well most of the bearings are seized and its missing the cable guard for the top part of the wheel and all the mounting bolts for the tensioner.... blah guess I'll be on the phone with that company tomorrow morning
seano11
Active member
- 878
- 103
- 43
- Location
- Edmonton Canada
Does anyone know where I could get new bearings for the trolly wheels ?
mdmorgan
AM3 U.S. Navy
- 1,085
- 102
- 63
- Location
- Forsyth, Ga.
I have not taken mine apart, is it bearings or bushings? A bushing you can just hone out a hair to clean it up then regrease and slap it back together. A bearing, well, you might luck out and be able to clean it up enough to get it moving again, but, if not, there should be a part number on the outside somewhere. I found the bearings I needed for the rear winch rollers on my M936 on ebay.
- 12,195
- 325
- 0
- Location
- gainesville, ga.
I had to take mine apart, no big deal, clean up, grease, put back together
seano11
Active member
- 878
- 103
- 43
- Location
- Edmonton Canada
Yup will be tearing it down and going through it all Does napa sell fake carc in spray cans ?
mdmorgan
AM3 U.S. Navy
- 1,085
- 102
- 63
- Location
- Forsyth, Ga.
That would be better answered in the paint and bodywork forum.
seano11
Active member
- 878
- 103
- 43
- Location
- Edmonton Canada
Just wanted to say thank you to everyone for helping me out with this
- 12,195
- 325
- 0
- Location
- gainesville, ga.
A few things I would change on the rebuild
!--- on the trolley wheels, either drill and cross drill the FRONT bolts for a grease fitting or get a set of rear bolts for the front, the way it is now, the rears wheels get grease but at times the fronts fail to grease.
2--- on the tensioner REVERSE the passengers side pin so the grease fitting is on the front side, and drill and tap for a grease fitting the tensioner control shaft (plug the old fitting hole), this too will bring the grease fitting to the front side, where the fittings are NOW, on the BACKSIDE of the tensioner , the fittings get knocked off by a bad wound cable
The above mods in no way affect the operation, the NEW grease fitting are out of the way so can not be knocked off, just make servicing easier
!--- on the trolley wheels, either drill and cross drill the FRONT bolts for a grease fitting or get a set of rear bolts for the front, the way it is now, the rears wheels get grease but at times the fronts fail to grease.
2--- on the tensioner REVERSE the passengers side pin so the grease fitting is on the front side, and drill and tap for a grease fitting the tensioner control shaft (plug the old fitting hole), this too will bring the grease fitting to the front side, where the fittings are NOW, on the BACKSIDE of the tensioner , the fittings get knocked off by a bad wound cable
The above mods in no way affect the operation, the NEW grease fitting are out of the way so can not be knocked off, just make servicing easier
Last edited:
seano11
Active member
- 878
- 103
- 43
- Location
- Edmonton Canada
Could someone do me a huge favor and tell me what size bolts are used to hold the tensioner to the winch should be 4 of them
- 2,731
- 856
- 113
- Location
- Oakwood, Ga
Seano "Oh Canada" lets see some pictures of your project!
