Guerrillaco
New member
- 27
- 25
- 3
- Location
- texas
-
Steel Soldiers now has a few new forums, read more about it at: New Munitions Forums!
M1083 crank no start, looking for a Mechanic to help me get it started
- Thread starter Guerrillaco
- Start date
Guerrillaco
New member
- 27
- 25
- 3
- Location
- texas
so the mechanic pretty much took everything apart here and notice the shared bolts off the flywheel they feel that fixing this will get the truck started and it's worth a shot what do you guys think and thank you so much for all the help this has been a fun nightmare.
The biggest question now is; “what caused those bolts to shear off”?
Have you flat towed the truck with the brakes cages? I’m wondering if there’s a problem in the transmission or drive train that caused this? Did some knucklehead try to recover this vehicle and cause this damage through improper procedure?
Ronmar
Well-known member
- 3,846
- 7,475
- 113
- Location
- Port angeles wa
Exactly!
Guerrillaco
New member
- 27
- 25
- 3
- Location
- texas
all those questions are valid and you know what I really do not know as I do not know the history on this vehicle when it was told here it came on a pretty large flatbed but the problem is it came to my Construction company and it was offloaded without me even seeing it. I'm just crossing my fingers that it can be fixed without the cost going up too much I really need this vehicle for my farm in Jamaica.
Been a common problem for years.
They were not torqued properly and no loctite was used. The trucks have vibrations anyway due to the hubs and driveshaft problems.
Loose Flex Plate Bolts
So from now on all LMTV's that come through my shop will get the flex plate bolts replaced torqued and lock-tighted. The US army must not own torque wrenches as this has happened with great frequency.
www.steelsoldiers.com
Most automatic transmission trucks with vibrations they tend to walk back the bellhousing bolts causing the bellhousing to crack or fall off the engine.
Once you get those old bolts out make sure the inside diameter & threads were not compromised.
I’m curious, if you know, Once loose, what causes all the bolts to shear at the same time? Initial torque on start up? Sudden acceleration? I can’t imagine that these bolts will all back out, or loosen, to a certain point and then shear. Interesting.
- 2,034
- 5,224
- 113
- Location
- Portland, OR
Fretting will cause them to fracture. Here's a treatise on the subject:
aeroenginesafety.tugraz.at
23.3.1.2 Failures of bolts and nuts [Aeroengine Safety]
Guerrillaco
New member
- 27
- 25
- 3
- Location
- texas
Guess what guys. The 6x6 is alive..
Attachments
Hopefully that is the end of your major repairs!
Guerrillaco
New member
- 27
- 25
- 3
- Location
- texas
I hope so I'm just trying to find the glass for the doors and all the locking mechanism and it should be good to go.
- 2,034
- 5,224
- 113
- Location
- Portland, OR
Woof. That had to be a mighty strong bill. Glad you got it taken care of though.
Guerrillaco
New member
- 27
- 25
- 3
- Location
- texas
6k for the job. way too expensive
coachgeo
Well-known member
- 5,147
- 3,462
- 113
- Location
- North of Cincy OH
including price of parts.... and labor.... he did good. Could have been way worse.
Guerrillaco
New member
- 27
- 25
- 3
- Location
- texas
I got some questions for the team where can I locate two door windows and the locking mechanisms for each door? I've been looking on eBay like crazy but I'm unable to find much.
Attachments
Guerrillaco
New member
- 27
- 25
- 3
- Location
- texas
she is rolling. thanks again for everyone's help.
Attachments
coachgeo
Well-known member
- 5,147
- 3,462
- 113
- Location
- North of Cincy OH
CONGRATS
coachgeo
Well-known member
- 5,147
- 3,462
- 113
- Location
- North of Cincy OH
Read thru this and other FMTV discussion groups/forums to get ideas on anything else that can be affected by the shake rattle and roll this truck was doing prior to shredding those bolts. Then go thru your truck with fine tooth comb to evaluate each to see if you need to take care of other things.
example.... get your driveshafts balanced. this maaaaayyyy be in part what started this whole mess from added vibrations from something amiss in your driveline. (out of phase? very unbalanced? frozen u joint? etc)
example.... get your driveshafts balanced. this maaaaayyyy be in part what started this whole mess from added vibrations from something amiss in your driveline. (out of phase? very unbalanced? frozen u joint? etc)
Ronmar
Well-known member
- 3,846
- 7,475
- 113
- Location
- Port angeles wa
Omni glass and paint in oshkosh WI. for the door glass.
Good luck with latch hardware. I went with trimark 2stage latches from a hotrod supply house and toyota tacoma/4runner handles…