shovelrocker
New member
- 7
- 0
- 1
- Location
- Bayside/Texas
Are there any other companies that make the spin on conversion besides Jatonka???
-
Steel Soldiers now has a few new forums, read more about it at: New Munitions Forums!
m35a2 Fuel Fiter
- Thread starter AZDeuce
- Start date
rustystud
Well-known member
- 9,280
- 2,984
- 113
- Location
- Woodinville, Washington
Are you talking about the fuel ones ? If so I just made my own. I posted the whole thing here. The oil ones are made by a few people. Go to eBay and look it up.
shovelrocker
New member
- 7
- 0
- 1
- Location
- Bayside/Texas
where did you post it???
You can get the spin on bases from Napa or cheap on ebay and just make your own mount system.
- 6,426
- 4,985
- 113
- Location
- Ft. Lauderdale, Florida
I built the very best fuel filter set-up for my Deuce and had zero problems.
That truck has the cleanest fuel tank there ever was. One of a kind.
I changed (renewed) all those fuel filters one time and never again. Lube oil filters too.
Turned out less expensive, like I am Mr. Frugal over here.
I thank all the SS people that helped me.
I am going back in the shed now to find even more stuff to give away..................
That truck has the cleanest fuel tank there ever was. One of a kind.
I changed (renewed) all those fuel filters one time and never again. Lube oil filters too.
Turned out less expensive, like I am Mr. Frugal over here.
I thank all the SS people that helped me.
I am going back in the shed now to find even more stuff to give away..................
rustystud
Well-known member
- 9,280
- 2,984
- 113
- Location
- Woodinville, Washington
Here it is.
https://www.steelsoldiers.com/showthread.php?123548-Spin-on-Fuel-Filters
Be sure to read the whole thing through.
KevinGaus
Member
- 91
- 0
- 6
- Location
- Lewisville, Tx.
On my second fuel filter change, I noticed this . Did I just get lucky the first time? Or is something out of wack?
rustystud
Well-known member
- 9,280
- 2,984
- 113
- Location
- Woodinville, Washington
Do you have all the washers and springs installed ?
KevinGaus
Member
- 91
- 0
- 6
- Location
- Lewisville, Tx.
I was up till 1:00 screwing around with all this. Setting the smoke cam, thanking the fuel filter cans apart. I’m happy to say I understand what’s going on in there now. And can deal with it accordingly. One had a rusty stuck and collapsed spring. I will swap it from the other engine.
rustystud
Well-known member
- 9,280
- 2,984
- 113
- Location
- Woodinville, Washington
For the first filter, it should be a "water/filter" unit with a10 micron filter. There are several companies that makes a good diesel fuel filter unit. Just depends on how much you want to spend.
GunInstructordotcom
Active member
- 97
- 112
- 33
- Location
- Castella, California
Do you still offer the secondary fuel filters for the multifuel engine? I have been trying to install the Napa o-ring gaskets and they are too small. They pop off when I try to put them in the slot in the housing.
m715mike
Well-known member
- 2,797
- 3,823
- 113
- Location
- Montgomery, Texas
Did you buy separate o-rings at NAPA or are you using the ones that came with the filters?
- 6,426
- 4,985
- 113
- Location
- Ft. Lauderdale, Florida
The O-rings are wrongs sometimes so one should just take it all apart to find double or triple O-rings in there making it impossible to do simple job.
Workin upside down backwards inside out is not good to try to resolve problems.
Wont hurt, a couple of mildly torqued bolts. Be One with your truck......
So just take it off and study and fix it.
Attachments
Last edited:
GunInstructordotcom
Active member
- 97
- 112
- 33
- Location
- Castella, California
I used the o-rings that came with the NAPA filters, the thinner ones. I stretched them and installed them before they shrank back down. I also used the washer gaskets that came with the filters for the top bolts. The bolt o-rings were trashed. The washers crush down into the o-ring groove. I hope they work when I start the truck up.
GunInstructordotcom
Active member
- 97
- 112
- 33
- Location
- Castella, California
Turned on the fuel pump, and the NAPA o-ring gaskets leak a bunch. Is there a replacement gasket that I can buy somewhere?
fpchief
Well-known member
- 1,041
- 220
- 63
- Location
- South Alabama
As with what frank said, take the assembly off and install gaskets where you can see them. I use the napa gaskets and have not ever had an issue. Something is just not on correctly.
m715mike
Well-known member
- 2,797
- 3,823
- 113
- Location
- Montgomery, Texas
The o-rings that came with the NAPA filters did not work for me. I purchased separate o-rings from NAPA (part numbers 5070 and 5131) as indicated in the Deuce parts quick reference spreadsheet. If you haven't seen that spreadsheet, you can check it out here:
Deuce Parts Quick Reference Spreadsheet
UPDATE TO LIST 8.18.2015 https://docs.google.com/spreadsheets/d/1e2C4UgWhEZvSnYHetyPAeVvto4MjcqQpbBQUtAUaWe0/edit?usp=sharing Please let me know if there is an error or anything to add. Thanks.
www.steelsoldiers.com
GunInstructordotcom
Active member
- 97
- 112
- 33
- Location
- Castella, California
Thank you for the o-ring information and the spreadsheet. I had been looking for that spreadsheet but had not found it.
- 6,426
- 4,985
- 113
- Location
- Ft. Lauderdale, Florida
I have put the information many times. Why not just change All the Deuce multifuel filters once and then never have to change any of them again.
It is a piece of cake, not difficult, not expensive.
Your choice, from 1 to 30 micron filters that won't let you down, installed in an area that is really easy to change.
It is a piece of cake, not difficult, not expensive.
Your choice, from 1 to 30 micron filters that won't let you down, installed in an area that is really easy to change.
Last edited: