-
Steel Soldiers now has a few new forums, read more about it at: New Munitions Forums!
M543A2 wrecker joins the family
- Thread starter bigmike
- Start date
wcuhillbilly
Member
- 421
- 5
- 18
- Location
- Devils Tower, WY
great job mike, Although,,,, why did you ditch the hard top for a ragtop? your truck, your choice....
The hard top was in pretty bad shape especially at the mounting flange (lots of rust). Also, with the gun ring, I thought it better to go with the rag top.
catskillpond
Member
- 159
- 1
- 16
- Location
- wurtsboro ny
Where did you get the data plates for the crane looked through this thread might need new glasses. Thanks Scott
see response #40 on previous page.
- 1,629
- 724
- 113
- Location
- Central NY
Went to dataplates.net and they only advertise an M35 set - did you have a custom set made from your old ones or are they just slow to update web site and do a whole lot more?
. I sent them my old ones and he replicated them one at a time. For all I know, he saved the info for future orders.
70deuce
Active member
- 936
- 121
- 43
- Location
- Franktown, CO
Boy if he saved the info for the wrecker data plates he might get a bunch of business. How much did all of them run?
sorry, it's been about a year since I ordered them so I don't remember what I paid. It was really reasonable.
70deuce
Active member
- 936
- 121
- 43
- Location
- Franktown, CO
Bigmike, I just emailed them and they can't seem to find your order. Greg said to email him at orders@dataplates.net so he can locate your order. It would be great if they could find your order so we don't have start all over again. I think there are a bunch of us out there that would go for a set of those plates. Thanks
wcuhillbilly
Member
- 421
- 5
- 18
- Location
- Devils Tower, WY
Plates would be nice,, mine are completely bleached and I have to go by memory as to what does what. Im ok with it but when the wife is operating and Im rigging, things get a little hinky... (helmet is usually required PPE)
Last edited:
sorry, I'm a little behind on this thread. I'll e-mail him tomorrow.
Gang,
I contacted Greg @ www.dataplates.net and he found the order with all the data plates he made for my wrecker. It's almost 100% complete except for some winch data plates which I didn't need to remove and replace. Feel free to contact Greg if interested in purchasing the data plates.
Last edited:
jhooah
Member
- 135
- 6
- 18
- Location
- Carrollton/Virginia
Weapons mounts are fine, but I think the real reason so many are out there surplus, was in-service, we merely rotated the M16s upside down and used the window elbow wing nut to secure them along the dash/window. if your rotate the nut, they lock in as if it was designed just for that purpose.
Love what you did to the wrecker, ours (in Virginia) is identical, with the exception of the labor going into her, I never had the time to peel the paint and finish putting on the new dataplate set I obtained after I returned from Afghanistan.
Really hard to get up to any speed, takes about a mile to reach 30mph too, engines putting out power, she just doesn't like to giddy up and go.
V/R W. Winget
Love what you did to the wrecker, ours (in Virginia) is identical, with the exception of the labor going into her, I never had the time to peel the paint and finish putting on the new dataplate set I obtained after I returned from Afghanistan.
Really hard to get up to any speed, takes about a mile to reach 30mph too, engines putting out power, she just doesn't like to giddy up and go.
V/R W. Winget
Csm Davis
Well-known member
- 4,164
- 393
- 83
- Location
- Hattiesburg, Mississippi
Mike you should look at getting the cab reinforcement plate that goes on the back wall and put it in before you hang the gun ring.
Sent from my SM-G930V using Tapatalk
I have a cab reinforcement plate. I didn't install it because the crane engage lever would be blocked and unable to operate. The lever is behind the driver's seat in the corner of the cab. I'll post some pics of my install and mods later today.
Csm Davis
Well-known member
- 4,164
- 393
- 83
- Location
- Hattiesburg, Mississippi
Yeah I think the wreckers and dump trucks had to modify the plates to clear the handle
Sent from my SM-G930V using Tapatalk
Sent from my SM-G930V using Tapatalk
wcuhillbilly
Member
- 421
- 5
- 18
- Location
- Devils Tower, WY
Im not familiar with the "plate" but knowing that stupid handle,,,, I would question, why not mod the handle......???? heat/bend forward some so that in disengagement position it is off the back wall by say 3 inches... and right in Funny bone range when engaged.....
Csm Davis
Well-known member
- 4,164
- 393
- 83
- Location
- Hattiesburg, Mississippi
I am with hillbilly you should be able to move it just slightly to miss the plate
Sent from my SM-G930V using Tapatalk
Sent from my SM-G930V using Tapatalk