Mep 006A won't turn over

[Powermaker16]

Good Morning Guyfang, Still having issues. I had to take a break on it due to work load. Just started messing with it again yesterday ironically. Fuel being dumped into Oil still and no power lug side of Output contactor. Mentioned above, the leather seals on the injection pump could be installed wrong allowing fuel into the engine. It cranks and runs, blows white smoke. It takes time for the little tank over the injection pump to fill back up each time as it drains down after sitting. I asked in a new thread I had started yesterday ( as I didn't think this was still active) if someone has a diagram or picture how they are supposed to be for when I take it apart. As for the power issue, I figured I would start with the cheapest thing first and replace the "Open Close" switch first as nothing happens when pressed with way.

 

[Guyfang]

I would suggest that you stay with one thread. First off that's the rules, but more importantly, its harder for you to get help. And its important for you to close the loop. If you don't tell us what you have done, then its impossible for us to help you. You need to start on one problem, and fix it. Often that fixes several other problems.

Changing parts is not the answer. It helps the economy, but that's about it. So pick one or the other thread and lets stick with just that thread.

 

[Powermaker16]

The lack of electricity was a new problem which prompted new thread since it was different than my original fuel issue. I want to make sure I can get power, that the electric generator part of this unit is still working before dumping another $1,600 into a new injection pump only to find out I’m not going to get power.

 

[FarmingSmallKubota]

The lack of electricity was a new problem which prompted new thread since it was different than my original fuel issue. I want to make sure I can get power, that the electric generator part of this unit is still working before dumping another $1,600 into a new injection pump only to find out I’m not going to get power.

If You want the injection pump rebuilt i would look into Area Diesel before spending that much money on a new one.

 

[Guyfang]

Why do you need a new IP?

 

[Ray70]

The kit to rebuild the IP is like $30 for the basic kit, or a little over $100 if you go with the upgraded metal governor weight basket.
If you only need to replace the umbrella seals that are leaking fuel into the crankcase, those are "external" to the pump and don't require any disassembly of the pump itself, just removing the pump from the engine and replacing the seals on the pump's input shaft.

 

[Ray70]

I am beginning to think the electrical part of this unit is going bad. I feel my rpm’s are high enough to get the 60 hertz I need, but the gauge isn’t moving at all, so I’m thinking it’s a power issue.

Nothing of the kind. It is not an electrical problem. Your throttle cable is hooked up wrong, or its hanging up on something. Do you have a multimeter that reads hertz? How do you feel that the RPM's are high enough? The gage, as mentioned before are not real reliable. But if you have AC voltage, you have hertz.

If you have a Home Depot nearby, for $28 you can get a Kill-A-Watt meter that will plug into the 120V courtesy outlet, it will accurately read volts and Hertz.
Most likely your gage or the frequency transducer that drives the gage is dead.

 

[Powermaker16]

Why do you need a new IP?

Well I thought I needed a new one due to the fuel leaking into the crank case. I missed the part about the two external seals. I now just need to find and order those.

 

[Guyfang]

You also need to read the -34 TM about how you pull the IP. Its not hard, but read the TM at least twice. Get it wrong, and you will regret it for ever. Say something here before you even get started. We can give you a few tips that will help.

 

[Ray70]

Look on ebay under Stanadyne 24371 injection pump kit.
Price ranges from $25 to $40
The 2 black rubber umbrella seals in that kit are the parts you need for your shaft leak repair.