Boogiessundance
Member
- 41
- 11
- 8
- Location
- Germany
How should voltage be applied to the small plug of the solenoid when there is no voltage applied to the ignition switch ?
-
Steel Soldiers now has a few new forums, read more about it at: New Munitions Forums!
No start
- Thread starter Boogiessundance
- Start date
Boogiessundance
Member
- 41
- 11
- 8
- Location
- Germany
For me the question is : Why does voltage come to the fusebox but not to the other side ?
Why do I have no voltage on the ignition switch , blower motor , wiper s ...
After I loosenedthe large connector on the bulkhead and screwed it back on , I had everything working normally for a short time .
- 560
- 391
- 63
- Location
- Jupiter/FL
You answered your own question re visit the bulkhead connector and be more thorough and look closely for possible causes. Maybe you missed something.
Just a thought
Sent from my SM-G975U using Tapatalk
Just a thought
Sent from my SM-G975U using Tapatalk
- 560
- 391
- 63
- Location
- Jupiter/FL
Also inside that bulkhead connector there are several buss strips that feed different parts of each fuse, possible cause of issue
Sent from my SM-G975U using Tapatalk
Sent from my SM-G975U using Tapatalk
Boogiessundance
Member
- 41
- 11
- 8
- Location
- Germany
I spend 2 hours cleaning and checking the connector .... but i noticed , that the 6 - legged Bus Bar Ground near the PB is without connection .
I mean , no cable is on it , 6 slots are empty .
The previous owner obviously rewired the Blazer and moved the Grounds somewhere else ...
- 597
- 694
- 93
- Location
- Okinawa, Japan
If you had, or made, a remote starter switch you could test it while it is on the vehicle.
- 890
- 1,332
- 93
- Location
- Rhein-Main Area, Germany
....... I think it's time to take a few photos and show them.
....... nobody gets any further here
Boogiessundance
Member
- 41
- 11
- 8
- Location
- Germany
what do you want to see in photos ?
Boogiessundance
Member
- 41
- 11
- 8
- Location
- Germany
I had bridged the two plus cabels of the ignition switch with a 12V from the bulkhead block . Then the starter moved , but the rest remained darg , including the glow circuit .
Where does the voltage come from to the ignition switch ? From the fusebox oe from the starter ?
- 597
- 694
- 93
- Location
- Okinawa, Japan
Has your truck been converter to 12 volt?
The ignition switch receives power from the fuseblock. When you turn to START it sends power to the starter relay under the dash. The relay then sends power (24 volts on stock trucks) to the starter solenoid.
The ignition switch receives power from the fuseblock. When you turn to START it sends power to the starter relay under the dash. The relay then sends power (24 volts on stock trucks) to the starter solenoid.
Boogiessundance
Member
- 41
- 11
- 8
- Location
- Germany
Thank you . The Chevy is comletely in its original condition .
The big connector outside fuseblok only has three PINs that carry voltage , right ? 2x 12V , 1x 24V
- 597
- 694
- 93
- Location
- Okinawa, Japan
I am not sure what block you are referring to. Can you post a picture of it?
Boogiessundance
Member
- 41
- 11
- 8
- Location
- Germany
sure
Attachments
- 597
- 694
- 93
- Location
- Okinawa, Japan
Sorry, I haven't ever had to work on my fuse block. Have you referenced the Technical Manual? The electrical schematics start on page 947 of this TM.
Boogiessundance
Member
- 41
- 11
- 8
- Location
- Germany
Thank you Curtisje , I haven´t had this version yet . will study the schematics well ...
Boogiessundance
Member
- 41
- 11
- 8
- Location
- Germany
There is News ! A friend measured the PINs in his CUCV connector and it looks like I don´t have 12V on three PINs , so melted fusible links after all ?
- 560
- 391
- 63
- Location
- Jupiter/FL
Fusible link on the fire wall that feeds the 12 V supply?
Sent from my SM-G975U using Tapatalk
Sent from my SM-G975U using Tapatalk
Boogiessundance
Member
- 41
- 11
- 8
- Location
- Germany
Unfortunately not that easy - the supply is 12V ....
Boogiessundance
Member
- 41
- 11
- 8
- Location
- Germany
Yiieeeehaw , she runs ! It was one of these fusible links , on the left side , lying on the valve cover . Not burned from the outside , but completely oxidized at the junction between cable and fuse . From the outside not to be recognized and temperatur dependend ( Valve cover ) , malignant .
Thank you guys , also for the patience !
Thank you guys , also for the patience !
Boogiessundance
Member
- 41
- 11
- 8
- Location
- Germany
