FreightTrain
Banned
- 2,730
- 13
- 0
- Location
- Gadsden,Al
I wouldn't mind having one like this but I gotta ask....How does a drive shaft that short have enough movement not to come apart or crash out when the middle axle articulates?
-
Steel Soldiers now has a few new forums, read more about it at: New Munitions Forums!
Now this is my kinda bob deuce!
- Thread starter FreightTrain
- Start date
bulldog_mack13
3/3 ACR
- 2,968
- 34
- 0
- Location
- Colo Springs, CO
send him a PM in egay. I talked to him a bit about his stencils on the dorr, nice guy
- 2,102
- 30
- 38
- Location
- Delta Junction, Alaska
Its still clean - they haven't tried it yet.
Lee in Alaska
Lee in Alaska
DanMartin
New member
- 1,276
- 16
- 0
- Location
- Hillsboro, Oregon (USA)
Is it just me, or does it look like it's missing a brake system on the rear axle? Maybe it's just the angle of the photo...but that looks weird.
FreightTrain
Banned
- 2,730
- 13
- 0
- Location
- Gadsden,Al
nah,it has drums.the other pictures showed them.
Elwenil
New member
- 2,190
- 40
- 0
- Location
- Covington, VA
It looks interesting but I bet the thing is hard to turn with all that rubber in the rear fighting you. I also don't like the fuel tank in the bed, even though there isn't a whole lot of alternatives. I would hate to have to climb up in the bed with a fuel hose every time I stopped for fuel.
- 10,868
- 768
- 113
- Location
- Appomattox, VA
You gotta admit, the fact that there are lots of good deuces available these days leads people to invent some interesting MV variants! I like it!
randyscycle
New member
- 467
- 3
- 0
- Location
- Rhoadesville VA (where!)
Definitely looks cool. Bet it rides like a buckboard though....as if they don't already... 
tiger422
New member
- 323
- 1
- 0
- Location
- Lakeland/Florida
My M35A2 rides better than my Jeep TJ off road much smoother.randyscycle said:Definitely looks cool. Bet it rides like a buckboard though....as if they don't already...
jwaller
Active member
- 3,724
- 19
- 38
- Location
- Columbia, SC
what a waste of a good truck. maybe a new owner can fix it. gotta love the 1980's TJ hooker light bar and lights.
res0wc18
Member
- 552
- 2
- 18
- Location
- Everett, Wa
did anyone ever figure out about the drive shaft issues with running a duel setup this short?
BFR
Rocket Surgeon
- 2,330
- 42
- 48
- Location
- North Georgia
I bet the wheelbase is close to that of a 275.
IMO shafts w/ double cardon joints could deal with the angles during articulation
IMO shafts w/ double cardon joints could deal with the angles during articulation
- 10,868
- 768
- 113
- Location
- Appomattox, VA
Just a thought, but perhaps it started out life as a -275 tractor? If so, I doubt there would be any problems with the flexing...
- 1,658
- 5
- 0
- Location
- Reidsville N.C.
Thats neet. If I tried something like that it would be upsidedown and backwards..
markaroe
Member
- 66
- 0
- 6
- Location
- Decatur, Al
Love it! This was one of my thoughts also. Just as much work as a single bob though.
I bet it'll crawl over most anything.
Put a Step tank on it!
I want to know about the axle articulation,
does the drive shaft drop out if they move too much?
Love the roll bar. I want to build one so the cross member rolls the lights down when not in use.
Where would you find a 275 tractor today, I haven't seen one.
I bet it'll crawl over most anything.
Put a Step tank on it!
I want to know about the axle articulation,
does the drive shaft drop out if they move too much?
Love the roll bar. I want to build one so the cross member rolls the lights down when not in use.
Where would you find a 275 tractor today, I haven't seen one.
Last edited:
gunboy1656
Active member
- 3,587
- 22
- 38
- Location
- Beaver Falls, PA
You must not be looking in the right places. There is one on egay right now.
Heck, even this truck keeps showing up on there.
Heck, even this truck keeps showing up on there.
XanRa
Member
- 584
- 5
- 18
- Location
- Cincinnati, Ohio
like this??