PowerstrokeNC
Member
- 430
- 1
- 18
- Location
- Greensboro, NC
Anyone have a good way to get the oil stains off CARC that inevitably happen with hydraulic fluid, grease etc...?
thanks
thanks
-
Steel Soldiers now has a few new forums, read more about it at: New Munitions Forums!
Oil Stains on CARC, how to remove?
- Thread starter PowerstrokeNC
- Start date
HanksDeuce
Well-known member
- 1,081
- 242
- 63
- Location
- Prairieville, LA
I typed "carc oil stains" in the little search engine box on the top right corner of the site.
http://www.steelsoldiers.com/showthread.php?11580-How-to-clean-oil-spots-on-CARC
http://www.steelsoldiers.com/showthread.php?11580-How-to-clean-oil-spots-on-CARC
- 3,871
- 497
- 83
- Location
- Gray Court SC
Purple power full strength and pressure wash will clean it the best it will come tan the hardest to keep clean will that flat porous paint will hold everything. So clean and touch up paint.
- 7,744
- 154
- 63
- Location
- Columbus Georgia
I use a product from Flynn Distributing (has a web site) and its a green degreaser.
It takes the grease stains out of the house carpet when I screw up and too lazy to take my shoes off - does not hurt the carpet or discolors it - it eats grease and oil.
I have a white baseball cap and after spraying that down when it is full of grease stains its perfectly white again - use it on my cloths as well before washing.
We use it at the shop for getting grease and oil stains out of the white trucks finish - does not hurt clear coat or paint and removes the stains even.
Its what I used to wash PB's engine with after doing the body work.
He will ship it and it comes in spray quart bottles.
It takes the grease stains out of the house carpet when I screw up and too lazy to take my shoes off - does not hurt the carpet or discolors it - it eats grease and oil.
I have a white baseball cap and after spraying that down when it is full of grease stains its perfectly white again - use it on my cloths as well before washing.
We use it at the shop for getting grease and oil stains out of the white trucks finish - does not hurt clear coat or paint and removes the stains even.
Its what I used to wash PB's engine with after doing the body work.
He will ship it and it comes in spray quart bottles.
ke5eua
Well-known member
- 2,568
- 41
- 48
- Location
- Baton Rouge (Central), LA
KansasBobcat
Member
- 641
- 8
- 18
- Location
- San Antonio, TX
A difficult problem. The older the CARC, the harder it is to clean. A perfect hand print on side of 998 in the 383 green. I tried Dawn, acetone, lacquer thinner, simple green and nothing worked completely..Was going to repaint anyway but tried RAPCO 383 without priming for touchup. The print could still be seen! However, after priming and then painting it was covered but of course did not match the old adjacent CARC very well. I've learned to be careful where I touch, especially with oily gloves!
- 1,958
- 427
- 68
- Location
- Culver City, CA
Leave it. It adds character 
- 6,067
- 4,429
- 113
Hot water running gently over it. Takes a while, and wastes both water and the power used to heat it....
Oil is lighter than water so will float up and the water will carry it away. The heat from the hot water decreases oil's viscosity and helps this along.
Works best on horizontal surfaces. I've got oil stains out of concrete driveways this way, as well as the bed of cargo trucks.
Oil is lighter than water so will float up and the water will carry it away. The heat from the hot water decreases oil's viscosity and helps this along.
Works best on horizontal surfaces. I've got oil stains out of concrete driveways this way, as well as the bed of cargo trucks.
searls84
Member
- 195
- 6
- 18
- Location
- Las Cruces, NM
O'Reilly's brand engine degreaser(non foaming) has worked great for me. Spray it and let it it set for a bit then pressure wash it off.
PowerstrokeNC
Member
- 430
- 1
- 18
- Location
- Greensboro, NC
Thanks for all the suggestions, I will do some experimenting.