Correct there was an A3 guy mudding up the thread a bit. I only say that because of the wheel questions not just tire sizes. This is great info and useful as I'm starting to look at tires after I move so I have a second set.
-
Steel Soldiers now has a few new forums, read more about it at: New Munitions Forums!
Tire Size Comparison 16 vs 14 vs 15.5
- Thread starter M1075
- Start date
Correct there was an A3 guy mudding up the thread a bit. I only say that because of the wheel questions not just tire sizes. This is great info and useful as I'm starting to look at tires after I move so I have a second set.
I had to look those tires up! Pretty cool didnt know that option existed. Some of our beet trucks could use those
gimpyrobb
dumpsterlandingfromorbit!
- 27,785
- 747
- 113
- Location
- Cincy Ohio
Low pressure and low speed, right? What is max speed?
gimpyrobb
dumpsterlandingfromorbit!
- 27,785
- 747
- 113
- Location
- Cincy Ohio
I've had pretty good wear from my 395 XZLs too.
The machine it's made for claims 50 mph as a top speed.
This is what I love to hear!
Special T
Member
- 495
- 21
- 18
- Location
- Wetside/ WA
Mich specs say they go on an 11" wide wheel. Not sure how you could run them dualled up. They look spec wise like a 12.5R20 XL that were run on the unimogs.
These come in 8in 10in and 12in and can be dualed
Sent from my SM-G860P using Tapatalk
Special T
Member
- 495
- 21
- 18
- Location
- Wetside/ WA
Are those some kind of striker wheel?
MRAP Maxx Pro Plus. They are just a reversed stud beadlock. The nuts face to the inside with a flat face. I actually came across the 10 and 12 wide ones on the yard that has the wreckers on them. Im assuming they are for heavier loads.
BenRoberts
Certified insane
- 1,367
- 208
- 63
- Location
- southwest/ohio
G177 11r20 and a 395/85/20 
Special T
Member
- 495
- 21
- 18
- Location
- Wetside/ WA
What kind of bolt pattern are the wheels? Where did you find them?
They are the only mrap wheels that will fit on a 5 ton. Feltz has them as well as the guy in Bells, TX that is on ebay.
Sent from my SM-G860P using Tapatalk
If I recall, they are thick aluminum. Check out the stud length and diameter.
Ive already secured studs of appropriate length. Just waiting to buy all the tires and wheels i need. Mock fitting next to 395s.
Sent from my SM-G860P using Tapatalk
Here is a potential spacer made from DOM tube. With longer stud, a spacer like it could be the gap filler, 1" to 9/16".
Pics of my rim project included which is similarly hub centered.
I would guess that duals would be close (or over) the legal limit. What would be their equal revs per mile, in a super single for the front? Edit...it appears 14.00 (from your pics)
An 817 would be sweet with them.
Pics of my rim project included which is similarly hub centered.
I would guess that duals would be close (or over) the legal limit. What would be their equal revs per mile, in a super single for the front? Edit...it appears 14.00 (from your pics)
An 817 would be sweet with them.
Attachments
Last edited:
The maxxpro plus uses a 395 up front with the 12.00s in the rear. They are within 1 inch of each other overall. With dual 12.00s you are not overwidth. It doesnt stick out any further than the 395 singles do.
Sent from my SM-G860P using Tapatalk