- 7,716
- 19,766
- 113
- Location
- Charlotte NC
Nice!! Really nice. Tires look great and the body looks great...Bought it!
Sent from my iPhone using Tapatalk
-
Steel Soldiers now has a few new forums, read more about it at: New Munitions Forums!
What did you do to your deuce this week?
- Thread starter Seth_O
- Start date
Hi Tim. Yeah, it was only $43. I may get to try it later this week when the temperature gets above freezing. I think the grease gets solid in between the pin and the leaf spring end too. Hopefully this works. I'll be sure to report back on it.
That is a really nice looking Deuce! I have a brother that lives in Swampscott Mass. a little ways from Boston.
pitpawten
Active member
- 259
- 199
- 43
- Location
- Centreville, Maryland
Nice, though I guess it says something about me that I'm more so drooling over your large set of cribbing blocks on the left in the picture than I am the steering setup
I received my Grease Fitting Regurgitator tool yesterday. It's really small but hefty. It appears to be very well made and if it works it's well worth the price. I may try it out this week. I have to get some light oil like WD-40 or penetrating oil first. I started and moved Brutus today to deal with 4" of snow and Ice. He started right up. I know Cattlerepairman will think I've jinxed Brutus by saying that.
- 6,426
- 4,985
- 113
- Location
- Ft. Lauderdale, Florida
What pump are you using?
Attachments
Today, I used my new grease fitting rejuvinator/regurgitator on the grease fitting I had previously drilled out and tapped. I'll be derned, that little tool worked! I was able to get new grease in and force the old out. It took about 3 tries using PB Blaster and a light brass hammer to free it up. I would have tried some of the other fittings, but it was snowing. After that Brutus took me to Unimart to get a double cheeseburger.
- 7,716
- 19,766
- 113
- Location
- Charlotte NC
Wow! That is great news Owen. Nothing like having the right tool for the job... And I'd bet the burger was a pretty good reward at the end
.
Yeah Tim it's a neat little tool. Very well made. I was just tapping it with about a one pound brass hammer. Picking my nose takes more effort. Can't wait to check the other fittings out. Some others may be stuck as well.Wow! That is great news Owen. Nothing like having the right tool for the job... And I'd bet the burger was a pretty good reward at the end
.
fleetmech
Well-known member
- 200
- 386
- 63
- Location
- Connecticut
Good to hear!
![[thumbzup]](https://www.steelsoldiers.com/images/smilies/icon_smile_thumzup.gif "Thumbs Up [thumbzup]"){kind=icon}
Hydraulic double ended ram.
Pump off a 5ton.
Attachments
- 6,426
- 4,985
- 113
- Location
- Ft. Lauderdale, Florida
familiar it is
Attachments
PSC 300 is the kit minus the 5ton pump and bracket. bracket was just a piece of 3/8 plate and I cut slots to weld in the mounts for the ram also just a piece of flat bar welded to the back for the lip. Pretty easy if you weld...just like anything.. easy if your used to doing it. This first install took some thinking but now it would be quick and easy.
Steering wheel was just showing I cut the center out of the original steering wheel and welded it into a smaller steering wheel so I could use the original steer shaft.
After the install I would say that if you are not doing a lot of off-roading then I would probably go with the Waterloo system. If I had to pay for fabrication then this kit would have been about $3500. I can now drive with my knee up the creek.
Well you did some fine job there HN6! I'm super impressed because I'm just terrible at welding. Never can seem to get the hang of it. My Brutus has power steering too. I believe it's a medium duty International Harvester or Navistar unit. Works like a champ.
jaba76
New member
- 4
- 15
- 3
- Location
- Massachusetts
Registered and insured. New drivers seat. All new light bulbs. Grabbed a jerry can and installed a new tie down strap. Changed the oil and filter. Cleaned up a few spots that were rusting on the tailgate. I discovered a mouse made it’s way into the heater so I need to figure out what to do there. I don’t think there is a nest. Next week fuel filter and tranny fluid! Oh I did something some here will probably cringe over. My tires are MRAP tires. The spare will not fit on the factory holder. I did not like the spare tire holder so I pulled that off. I may mount a tool box in its place. Removing that really cleaned up the look. I love this thing! Ton of fun, or should I say 2.5 tons of fun!
Sent from my iPhone using Tapatalk
Sent from my iPhone using Tapatalk
- 280
- 933
- 93
- Location
- Knoxville, TN
Your not alone when i swapped over to 395's with mrap wheels i removed my tool carrier and spare tire carrier. I haven't decided what i want to do yet. i have decided on three options 1 modify the original tire carrier for the 395's, which I've read how to do on here, 2 add another step/box beside the original drivers, or 3 do a dual fuel tank. decisions decisions.