CUCVLOVER
Active member
- 2,352
- 9
- 38
- Location
- west Tennessee, just outside Milan
Ok. Thanks
Still the 6.2 diesel?
-
Steel Soldiers now has a few new forums, read more about it at: New Munitions Forums!
What have you done to your CUCV today/lately - Part 2
- Thread starter Warthog
- Start date
Still the 6.2 diesel?
3jumpjeep
Member
- 157
- 1
- 18
- Location
- Linsdale, TN
Yes, I plan on keeping that 6.2 healthy for a long time.
Sent from my SCH-I545 using Tapatalk
CUCVLOVER
Active member
- 2,352
- 9
- 38
- Location
- west Tennessee, just outside Milan
Cool.
Good luck with the 6.2 I like em but I just needed more power. That's why I did the 454 swap
3jumpjeep
Member
- 157
- 1
- 18
- Location
- Linsdale, TN
I tow a fifth wheel camper with it...slowly. It's underpowered, but does what I need it to. Mostly it works on my property and stays local.
Sent from my SCH-I545 using Tapatalk
CUCVLOVER
Active member
- 2,352
- 9
- 38
- Location
- west Tennessee, just outside Milan
There ya go
Chevybrit
New member
- 177
- 2
- 0
- Location
- Northern Pasquotank NC
rustystud
Well-known member
- 9,298
- 3,072
- 113
- Location
- Woodinville, Washington
Your truck looks just like mine now with those DuraTracs ! Except mine is tan.
Never liked the tan color. I also love the fifth wheel ! Now If I can just convince the wife to sell that 24ft trailer and get a good fifth wheel !
gottaluvit
Well-known member
- 1,786
- 28
- 48
- Location
- Bethesda, OH (AKA: Flyover Country)
Just yesterday in mine I was pulling away from a light as it turned green and punched it and both tires lit up kicking the rear sideways. I was impressed. The 6.2 is slow pulling a load uphill but it still has plenty pep when asked.
- 34,012
- 1,810
- 113
- Location
- GA Mountains
Both trucks have been neglected. The contact truck has been driven once since the GA. Rally and the ambulance I can't even remember. So, yesterday I took the contact truck up to the next county and back. My left knee wasn't liking the clutch pedal at all. Parked that and jumped in the ambulance. Despite sitting for months (and it looks it), it started right up. Took it up to the next county and back as well. Just so you know, it still has FL fuel in it from March when it was brought up to GA. Going to need to drive a tank out and freshen it up.
Attachments
3jumpjeep
Member
- 157
- 1
- 18
- Location
- Linsdale, TN
Two too nice to sit.
Sent from my SCH-I545 using Tapatalk
Sent from my SCH-I545 using Tapatalk
- 4,292
- 1,779
- 113
- Location
- Edmond, Oklahoma
Used it to haul a free 300 gallon fuel tank to north end of ranch.
It's a ton more stable back there strapped down than it looks.
The CUCV bed cargo tiedowns are very handy.
Free gun safe is in trailer. That will go elsewhere.
It's a ton more stable back there strapped down than it looks.
The CUCV bed cargo tiedowns are very handy.
Free gun safe is in trailer. That will go elsewhere.
Last edited:
3jumpjeep
Member
- 157
- 1
- 18
- Location
- Linsdale, TN
Free sounds good.
Sent from my SCH-I545 using Tapatalk
Sent from my SCH-I545 using Tapatalk
- 4,292
- 1,779
- 113
- Location
- Edmond, Oklahoma
Very!!
Red diesel will go in tank.
The free safe is a 35 gun model and is a very well known brand. And is like new!!
Will not post pics of that for OPSEC.
iacucv
Member
- 153
- 1
- 18
- Location
- Spencer, IA
Ditched the threaded insert idea for my grenade t case shifter knob. Went out to the shop and decided to see how the Miller liked the cast metal... Worked pretty good. Not the prettiest weld but solid, still learning this new welder. Put some self etch primer on it, clocked exactly how I wanted it with no shimming. Paddle to the left so you can firmly grab the body of the "grenade" to shift. Will try to post pics soon. Also picked up insulation for the shop, gotta make it warm enough to get my floor pans replaced this winter!
Welded the front diff
Thursday I Attacked the front diff of my M1009 with my welder.
Many many people have never tried a welded front and tell me how bad it is. With manual locking hubs I feel a welded diff is a fantastic solution!
Spent the weekend in the mountains playing with snow and ice. My M1009 with less than $750 invested was the best performing vehicle out this weekend.... Except for when it comes to stopping in the snow.
Thursday I Attacked the front diff of my M1009 with my welder.
Many many people have never tried a welded front and tell me how bad it is. With manual locking hubs I feel a welded diff is a fantastic solution!
Spent the weekend in the mountains playing with snow and ice. My M1009 with less than $750 invested was the best performing vehicle out this weekend.... Except for when it comes to stopping in the snow.
Hal O'Peridol
Member
- 121
- 4
- 18
- Location
- Blaine, WA
Put in a new driven gear for my speedometer. Now, instead of having no idea how fast I am going on the highway, I get to choose between 45 and 65 miles per hour.
Driven gear for the M1009 is the 41 tooth mustard yellow one. No parts houses carry them. Called a transmission repair shop, they don't have them either. Owner said he got them off of Amazon when he needed one. SMDH.
Driven gear for the M1009 is the 41 tooth mustard yellow one. No parts houses carry them. Called a transmission repair shop, they don't have them either. Owner said he got them off of Amazon when he needed one. SMDH.
- 1,512
- 1,696
- 113
- Location
- Puget Sound, WA
The speedo needle in mine wave at me while I'm driving, then reads anywhere from 5 to 10 MPH too fast. I just look at the GPS on the dash for speed. I can also turn on the K-band radar unit and it'll display my speed. It's one of those repairs that's prioritized so low it'll never get done.
cucvrus
Well-known member
- 11,474
- 10,441
- 113
- Location
- Jonestown Pennsylvania
I have had great success just putting cable lube on the cable after pulling it out and then reinstalling the cable. Happy Holidays. Good luck. Spray a little cable lube into the speedometer head. Don't go crazy. The cable is a bit dry after 30+ years.
cucvrus
Well-known member
- 11,474
- 10,441
- 113
- Location
- Jonestown Pennsylvania
Last edited:
richingalveston
Well-known member
- 1,715
- 120
- 63
- Location
- galveston/Texas
I have an eaton e locker and yes any front locker makes the truck awesome.
I thought all of the parts in the diff were heat treated and thus not good to weld on but I don't know it all.
please reply to this thread when it fails, I will hold out on any judgement till then.
keep an eye on your hubs, I have a problem with the left one locking on its own. I pulled it apart and checked, can't find anything wrong and there is not a bunch of grease build up so no reason but it keeps happening (warn's are in my future). With one hub locked, your front drive shaft is going to spin, thus you might have premature wear and MPG loss. If it is just a trail rig and not DD then probably nothing to worry about.
Thanks
Rich
I thought all of the parts in the diff were heat treated and thus not good to weld on but I don't know it all.
please reply to this thread when it fails, I will hold out on any judgement till then.
keep an eye on your hubs, I have a problem with the left one locking on its own. I pulled it apart and checked, can't find anything wrong and there is not a bunch of grease build up so no reason but it keeps happening (warn's are in my future). With one hub locked, your front drive shaft is going to spin, thus you might have premature wear and MPG loss. If it is just a trail rig and not DD then probably nothing to worry about.
Thanks
Rich