A
Makin me want some 24 bolt wheels for myself heh
-
Steel Soldiers now has a few new forums, read more about it at: New Munitions Forums!
What have you done to your HMMWV today/lately
- Thread starter Warthog
- Start date
- 2,975
- 4,356
- 113
- Location
- Olympia/WA
honestly, they're a pain. You torque each bolt twice, so for 4 wheels you're talking 192 clicks of the torque wrench. So twice as long to bolt together, and twice as long to take apart.
Only really needed if you're running your truck heavy (over 14k lbs)
My most dreaded part is honestly the run flat insert. Ratchet strapping and prying that thing is pretty lame. Makes me wonder if a tire shop could at least handle that part if I bring them the tires and run flats.
- 2,975
- 4,356
- 113
- Location
- Olympia/WA
Some are willing to try, but you will likely be paying them by the hour for them to figure it out.
I found if you ratchet strap one side enough to give the runflat a nice curve to it, then use plenty of tire soap, it pretty much slips right in.
I also take the short hook strap piece off the ratchet strap, and run the hook from the longer strap back to that bar. Makes it so you aren't dealing with as many loose ends or odd bulges in the straps while installing.
Removal I use the tree method. Strap tire to tree on two sides, and run strap from run flat to vehicle of choice. I used farm tractor because it's slow and I can see what's happening.
- 333
- 508
- 93
- Location
- Cleveland,TN
Let us know how that goes.........................................
Autonomy_Lost
Well-known member
- 687
- 1,537
- 93
- Location
- Pennsylvania
Crazy thought...what if you cut the run flat into two pieces?
- 333
- 508
- 93
- Location
- Cleveland,TN
Bu cutting your strap off so there is just enough to complete the loop and "lock" itself when it is ratcheted it gives you more room on the ratchet to pull it up further. Just my 2 cents.
Oh I’ve already done it a while back, new BFG Bajas on mine. I yanked the run flat out by using 2 trucks pulling apart, similar to @Coug
I just have to do it on another 8 tires soon is what I’m not looking forward to lol
- 333
- 508
- 93
- Location
- Cleveland,TN
No No No .......... Getting the tire shop to change them!
Oh - well I’ve got a local guy, not a chain. He did the lock ring tires/wheels on my deuce, may be willing to give these a try. Shall find out heh
I feel like that might cause an imbalance with both of them not being tight against the rims and just bouncing around the outer wall of the tire.
Autonomy_Lost
Well-known member
- 687
- 1,537
- 93
- Location
- Pennsylvania
You might be right. I know there is a magnesium 3-piece run flat, so I was thinking maybe there is a way.
- 333
- 508
- 93
- Location
- Cleveland,TN
If he does lock rings he probably will do anything!!!
Me neither. Never seen one before.
- 388
- 762
- 93
- Location
- Mansfield, PA
There are a number of You Tube videos about installing the run flats. I'd suggest checking them out.
Gastrap
Active member
- 328
- 158
- 43
- Location
- Central Iowa
They're fun for sure. I used a strap that comes with over-tire tracks for a skid loader. No hooks makes it easy to work with.
- 6,930
- 9,587
- 113
- Location
- Papalote, TX
There is a tool in the 57K0267 tool kit that EVERYONE that owns a HMMWV should have.
I have never tried that tool, I always go with bead locks, maybe someone can comment on that!
I have never tried that tool, I always go with bead locks, maybe someone can comment on that!
Humvee HMMWV Kippertool 57K0267 Vehicle Tool Kit 5180-01-387-5455 NOS | eBay
PN: 57K0267 NSN 5180-01-387-5455 5180013875455. BLIND FASTENER INSTALLATION KIT. TIE ROD SEPARATOR. GEARED HUB SOCKET WRENCH. GEARED HUB INPUT SEAL INSERTER. GEARED HUB SEAL INSERTER. YOKE SEAL INSTALLER.
www.ebay.com
I did the same thing, but when the runflats are covered in lube/grease then you look like a dog that just rolled in fresh droppings when finished.They're fun for sure. I used a strap that comes with over-tire tracks for a skid loader. No hooks makes it easy to work with.
AAVP7
Well-known member
- 217
- 262
- 63
- Location
- Dortmund, Germany
You mean that runflat ratchet thing ? I used that several times. Works nicely, and especially the "release" part is way more controlled than with a cargo strap ratchet.
However, I found my runflat tool was bending under stress, so I welded an extra connection into the open end of the "U"-shaped frame.
A friend of mine owns the local tire shop, and we worked on several Humvee tires. Besides the runflat tool, I also used a set of "Cheap Chinese tire spreaders" like these :Ebayde link . Those help to keep the tire sidewalls spread while you fumble the beadlock or runflat in.
My buddy was so fascinated by those tools that he made me leave the tools with him, and I bought new ones. Still a good deal, since we worked with three people a whole day, and he charged nothing.
Last edited:
- 481
- 1,112
- 93
- Location
- AL
Cleaned out the catalytic converter on my M1151A1. Turned it intake end down in a 5 gallon bucket to catch the mess. LOTS of BB-sized carbon granules fell out before even starting the process. Used a very concentrated solution of Simple Green followed by a 5 gal bucket of scalding hot water. After donning safety glasses, I then sprayed an entire can of carb cleaner followed by a high pressure water hose rinse. I used a leaf blower to dry with very little restriction in flow noticed at the output. Using the AL sunshine to finish drying up any residual moisture.
Before
After
Before
After