- 556
- 53
- 28
- Location
- Winston Salem NC
Where is the best (least expensive) place to get a new plastic wiper motor for my deuce? 
David
David
-
Steel Soldiers now has a few new forums, read more about it at: New Munitions Forums!
Where to buy a plastic wiper motor?
- Thread starter 82ABNMP
- Start date
- 1,878
- 15
- 0
- Location
- Glen Arm Maryland
Pm Country AKA Dave from Eastern..
- 1,926
- 30
- 48
- Location
- Irmo, South Carolina
82,
If you get a new plastic wiper motor that doesn't run right out of the box, I found that giving the motor a pulse of compressed air, right in the entry nipple freed up mine. Mine didn't work, and after taking it apart and finding nothing, I put 90psi into it in a blast and she started running. I guess the bypass valves are not always seated during assembly.
Rick
If you get a new plastic wiper motor that doesn't run right out of the box, I found that giving the motor a pulse of compressed air, right in the entry nipple freed up mine. Mine didn't work, and after taking it apart and finding nothing, I put 90psi into it in a blast and she started running. I guess the bypass valves are not always seated during assembly.
Rick
- 7,584
- 363
- 83
- Location
- Cheyenne, WY
If you've got to replace one i'd upgrade to the metal ones. About same cost.
- 8,539
- 2,758
- 113
- Location
- Monrovia, Ca.
Lube it with MMO also. IMHO, do not buy nes plastic ones. They are jnk. Best bet is to find old used ones and change the levers.
Blood_of_Tyrants
Active member
- 1,614
- 11
- 38
- Location
- Lebanon, TN
Try taking the end off and putting some air tool oil in it. I had one go out and after I put the air tool oil in it, it worked for over half an hour!
- 4,763
- 1,164
- 113
- Location
- Gaithersburg, MD
Call Memphis Equipment and ante up for two new metal wiper motors...or buy an electric wiper motor kit.
- 7,584
- 363
- 83
- Location
- Cheyenne, WY
Antelope Valley has both the plastic and metal ones. There's an electric set on ebay too.
clinto
Moderator, wonderful human being & practicing Deuc
Staff member
Administrator
Super Moderator
Steel Soldiers Supporter
Supporting Vendor
- 12,596
- 1,132
- 113
- Location
- Athens, Ga.
Memphis Equipment has been running the electric kits on ebay. And they are bringing big bucks.
- 556
- 53
- 28
- Location
- Winston Salem NC
wiper motor
Yep, I have tried everything..taken it apart used oil, air ect, the small valve where the red buton is located is shot...Thanks!
Yep, I have tried everything..taken it apart used oil, air ect, the small valve where the red buton is located is shot...Thanks!
- 3,021
- 222
- 63
- Location
- eldersburg maryland
why plastic?? they are junk. i have never had one last for more than a year. get a good metal set and you are good for life.
saddamsnightmare
Well-known member
- 3,618
- 80
- 48
- Location
- Abilene, Texas
December 13th, 2009.
82NDABMP:
Drop me a line and I'll send you one or two of the plastic wiper motors. I couldn't get them off the truck fast enough so I could put metal ones on from Desert Deuce. If I had had the deep pockets at the time, I would have used the electric motors if I could have found them. But at least the exhaust air keeps you awake at night. I just wish I could find an in-line needle valve for the hose to cut the passengers wiper out when I don't need it (like on the interstate).
Cheers,
Kyle F. McGrogan
82NDABMP:
Drop me a line and I'll send you one or two of the plastic wiper motors. I couldn't get them off the truck fast enough so I could put metal ones on from Desert Deuce. If I had had the deep pockets at the time, I would have used the electric motors if I could have found them. But at least the exhaust air keeps you awake at night. I just wish I could find an in-line needle valve for the hose to cut the passengers wiper out when I don't need it (like on the interstate).
Cheers,
Kyle F. McGrogan
- 556
- 53
- 28
- Location
- Winston Salem NC
quick fix
I was just looking for a quick temp fix to get me thru the winter.
David
I was just looking for a quick temp fix to get me thru the winter.
David