-
Steel Soldiers now has a few new forums, read more about it at: New Munitions Forums!
What did you do to your deuce this week?
- Thread starter Seth_O
- Start date
- 6,556
- 13,941
- 113
- Location
- Hawthorne, NV.
Looks good, keep us posted. Also I like the way you have your lights set up A2 & A3, and lollipop lights. You may have room left for a couple 5 ton warning lights.
Attachments
Last edited:
- 6,556
- 13,941
- 113
- Location
- Hawthorne, NV.
What's the condition of the tires, and where in Montana?
Jericho
Well-known member
- 1,180
- 69
- 48
- Location
- Landaff NH
I live remotely and work for UNC SAm , drive a lot of narrow DIRT roads to work site each day , Noticed I was scareing the crud out of people who were passing me in the dark winter months , They would tell me the narrow light pattern made them think I was a small truck ,then WOW that's a big truck , so added low beams on the fenders , and the yellow beacon , NOW THEY SEE ME COMING
- 6,556
- 13,941
- 113
- Location
- Hawthorne, NV.
Got the PTO installed, and then the clouds rolled in and it started snowing. It's supposed to be cold but clear tomorrow so I'll get a jacket on and get the shift linkage installed.
rustystud
Well-known member
- 9,284
- 2,994
- 113
- Location
- Woodinville, Washington
Yes. The input shaft is always turning except when the clutch is pushed in. So the turning shaft will turn the countershaft and unless the output shaft is being held by something it too will spin just by friction.
jbayer
Member
- 675
- 7
- 18
- Location
- St. Aug., FL/ McGrady, NC
Pictures Please Jericho. Scratch that, Valence pointed them out to me. Duh!
Last edited:
nchittendon
Active member
- 544
- 28
- 28
- Location
- La Crosse, Wisconsin
I hope to get her jacked up and start flipping the hubs today. Don't have my wheels/tires mounted yet, but I can still flip the hubs and single it out until I'm ready.
- 2,112
- 555
- 113
- Location
- Davis County, UT
He did, just on the last page, post #6758.
jbayer
Member
- 675
- 7
- 18
- Location
- St. Aug., FL/ McGrady, NC
Thanks Valence, I did'nt think to look back.
- 2,112
- 555
- 113
- Location
- Davis County, UT
No problem. It's not always easy to tell or think of everything.
Jericho
Well-known member
- 1,180
- 69
- 48
- Location
- Landaff NH
no worries, is a fast and easy install. lines up naturally , couple of holes and a couple of wires and , Wham its done . Works for me!
gimpyrobb
dumpsterlandingfromorbit!
- 27,786
- 755
- 113
- Location
- Cincy Ohio
- 6,075
- 4,448
- 113
Silverstate55 and I replaced the complete clutch assembly and rear main seal in Carnac's M35A2 a couple of weeks ago.
This was a learning experience for me, as I had never done a clutch before. It was pretty much a 15 hour job, with both of us working on it.
A piece of channel wedged from windshield to rear of cab is a must. This would have been much more awkward with just a transmission jack.
If you have to replace the rear seal, replace the clutch while you're at it if it is even remotely questionable. This is a big enough job you don't want to do it again if you don't have to.
Carnac's truck was loaded onto my gooseneck, which made crawling under it less of an aggravation.
Silverstate55 is a good teacher. It is evident he teaches for a living.
Some pics -
This was a learning experience for me, as I had never done a clutch before. It was pretty much a 15 hour job, with both of us working on it.
A piece of channel wedged from windshield to rear of cab is a must. This would have been much more awkward with just a transmission jack.
If you have to replace the rear seal, replace the clutch while you're at it if it is even remotely questionable. This is a big enough job you don't want to do it again if you don't have to.
Carnac's truck was loaded onto my gooseneck, which made crawling under it less of an aggravation.
Silverstate55 is a good teacher. It is evident he teaches for a living.
Some pics -
Last edited: