Search results

I wonder what a replacement membrane filter would cost for something this big.

If this happens, can the engine be saved or does it become scrap?

I hear some say they don’t like the NHC250. I’m wondering why. In 2019 I was in Utah and had to make a mad dash home to Michigan. I put my foot on the floor, only stoped for food, fuel and a little shut eye. I beat that engine for two and half days at full throttle. If these are bad engines...

I will be there parked with the MVPA convoy. Stop by and see what the convoy looks like. BTW there will be another one in 2023. When you see how much fun it is you may want to start making plans.

Sorry about that. Please change he for she and his for hers. My observations remain. You are infected and have no idea just how sick you’re going to get. o_O welcome to the ward!

Come on Gunny! You know very well that he is already in too deep. Every cell in his body has been infected with Mthrax. There is no cure! We are all doomed… There’s no point in hiding it. We all find out after there is no way out. :eek:

Here is the logic: A nice Jeep costs more than a 5 ton or a deuce. Why you ask… The jeep has a much higher “spousal approval rating”. It fits in the garage, it’s small (cute) and easy to drive. Chics dig ‘em. While this may not make any sense to us, it is the rule. This is one strange hobby...

I don’t have a vehicle with glow plugs, so pardon my ignorance. My question is, if a push button can replace a $100.00 part, why would anyone replace the “automatic” circuit board that causes nothing but trouble? I have to be missing something here… If this is my truck, I hold down the button...

David, I’m sorry to hear of your loss. This is far more important than anything O.D..

Welcome to the ward. There is no known cure for this affliction. However, this is the best place for you to be. You have obviously done your homework. Your list is right on track. It sounds like you are starting with a solid truck. What ever you don’t know about that truck yet, you will learn...

Simple… Buy her a nice MV. Then you’ll have two. ;)

The thing I like about sand color is the truck stays a lot cooler when it’s sitting in the sun.

In the last two weeks I switched out my drivers seat with an air ride seat, installed a 24 volt inverter so I will have 120 VAC while running down the road and repaired some minor stuff in preparation for the upcoming MVPA convoy.

Great idea. We have a his, hers and ours. :) His = M37, Hers = M151A2, Ours = M934.

M35A2-AZ, you did an outstanding job replacing that floor. POR15 is a great rust stopper. It does require a top coat. I’m told it can’t hold up to UV light and will turn chalky. I know it isn’t restoration correct but I like using Rino Liner as a top coat on floors. It really holds up. I know a...

This is how you fix a rusty floor. I would prime The new steel with an epoxy primer ( DP90 is the best). I would then use a wire brush to knock off any loose stuff on the remaining areas with surface rust and prime these areas with POR15 or a product called Chassis Saver. Then give it a few...

Bump

The number I have for Brooks is 727-871-4283. I sure hope they are still around. I had them rebuild the carb on our M151a2 and the thing runs like a top. No flat spot, no running with the choke out a 1/4 inch. Whatever they do to these carbs, works. Some of my friends have had the same results…

Hey Simp, I lIke your avitar!

Good advise to check the 12 volt batteries first. Get them up to charge. Then you can use a 24 volt Battery Tender. You can install the tender on the truck and connect to the 24 volt battery posts. Route the power cable somewhere with easy access. No need to disconnect the tender from the...