Search results

The biggest problem with the factory setup is when you change a filter. I have changed 2 of the factory filters and both times I had to crank and crank and crank (for a long time ...I was actually worried about the batteries) to get it to fill and finally ( after using a little either....very...

Oh you will need to buy 2 barbed fittings at the local hardware store also!:-D

Walmart...boating section....base and filter under 30$ and it is a screw on so you can prefill it..easy and cheap and the replacement filters are 7$ works great on my M1009 and I am running WVO 3 months and haven't changed it yet!:-D

Peptobismol has nothing on your truck! LOL:razz:

The square fuel filters are junk too. Go with a spin on from Napa or Go to Walmart in the boating section and pick up a filter kit for under 30$ filters are 7$ and you can prefill them (makes changes easy).

Souds like you are either cranking for a long time or have a direct short to ground. Since it was cranking, how long are you trying to start it?

Walmart!....Boating section....Kit is 30$ If I remember correctly...Filters are there too 7$ spin on and are able to be prefilled easily so no more cranking till the batteries die to fill the filter. I bought two fittings from the harware store and used my old bracket to mount the new filter...

It won't be a problem lots of people are bringing their civy vehicle and either camping out or getting a hotel room. I am sure you can tag along with someone for a trail ride if your toys have not been released by the government. Fi and Sat dinner looks to be covered so all you should have to...

Hey servo I will be there! many of us are CMVPA. Here are the other links! http://www.steelsoldiers.com/upcoming-events/30709-official-nc-rally-uwharrie-june26-28-a.html?highlight=official http://www.steelsoldiers.com/upcoming-events/30742-nc-uharrie-rally-you-going.html?highlight=uharrie

Bump!

Always good to have the experienced people on the trip. Thanks to ALL of you who are going to make this rally great!!!:-D:-D

I had problems with my square fuel filtrer(on the firewall passengers side) and replaced it with a Filter kit from Walmart(back in boating section ) its a screw on filter with more capacity and you can prefill it so your IP doesn't run dry unlike the square ones which are a pain to change.

Anything is restorable if you want to throw enough $ in. From the pictures looks like a good candidate though. Is that a Ford GP?

Is the exhaust manifold plugged up? Are you using the stock fuel filter? I changed my fuel filter to a spin on so I could prefill it, the square filters are terrible and take forever to fill after you change them. Have you tried spraying auto trans fluid in the intake(not a great idea but will...

Most people find that it's the relay I would check there before I go anywhere else!

I would try GL but so far I am 2 for 2. If it goes above 1500 I would bid on a GL one close to your home so you could look it over and maybe they would let you try to jump start it?

Nice truck

The only thing I could think of that could make it any better is some sort of water sensor on the inlet line to shut a solenoid valve to the bowl and shut off the centrifuge. Or a water sensor that would drain only the water off of the heating tank would be awesome!:-D

Not much is plug and play but I put my system together and it works great. NICE BOWL! avengeusa! I clean my bowl about every 55gal with a rag while hot and you remove about a 12oz can size of crud (looks like axle grease) from the sides. Avengeusa as a metal fabricator how about making an...

ROFLMAO too funny. Actually I did not know about the zinc plating! Thanks! I have only used it to clean out radiators (steel) and it does a great job. HMMM I always wanted a hydrogen generator.......Kidding only kidding!!!!!:wink: