-
Steel Soldiers now has a few new forums, read more about it at: New Munitions Forums!
Search results
-
mep 004a no fault lights working plus more
Ok But I don't know where P5 is at so I will have to take the SP box out and find it because it is marked inside the box. Then start trouble shooting. My assistant has the wrench to take off connectors so I'm screwed for tonight. Kris- KLChurch
- Post #316
- Forum: Generators
-
mep 004a no fault lights working plus more
Took the ground jumper off and no engine start. Will be doing the rest of the instructions tonight. Kris- KLChurch
- Post #314
- Forum: Generators
-
mep 004a no fault lights working plus more
No I have not replaced the lights yet but I will try to buy them tomorrow. Also there is one of the panel lights out. I can change out the unimportant lights to the important lights in the mean time if you can tell me. Only two lights are burned out. Kris- KLChurch
- Post #312
- Forum: Generators
-
mep 004a no fault lights working plus more
Ok This will take a while, but I'm on it. You have been super duper on this mission. Kris- KLChurch
- Post #310
- Forum: Generators
-
mep 004a no fault lights working plus more
Engine started and ran OK.- KLChurch
- Post #307
- Forum: Generators
-
-
mep 004a no fault lights working plus more
Sounds like we are getting close- KLChurch
- Post #305
- Forum: Generators
-
mep 004a no fault lights working plus more
Hooked up the IP ground terminal directly to the battery. Cranked engine twice for 3 secs. Got air and fuel each time. Kris- KLChurch
- Post #303
- Forum: Generators
-
mep 004a no fault lights working plus more
Ok It will be a few mins Kris- KLChurch
- Post #302
- Forum: Generators
-
mep 004a no fault lights working plus more
unjumped, and connector in place. Start mode Got 24VDC at the IP wire disconnected Put wire back in place. Cracked the line going to the injector (Top Left) cranked the engine several times No Fuel Kris- KLChurch
- Post #300
- Forum: Generators
-
-
mep 004a no fault lights working plus more
Got 24 VDC with the start engaged. Kris- KLChurch
- Post #297
- Forum: Generators
-
mep 004a no fault lights working plus more
ok batteries are full testing in a couple of mins kris- KLChurch
- Post #296
- Forum: Generators
-
mep 004a no fault lights working plus more
This is the IP fixen to be tested and the wire off. Please look at the wire holding I guess the throttle. Is this in the correct position? Battery is still charging Kris- KLChurch
- Post #294
- Forum: Generators
-
mep 004a no fault lights working plus more
OK The one battery is charged and the other will be in an hour. Kris- KLChurch
- Post #293
- Forum: Generators
-
mep 004a no fault lights working plus more
Just to add. when the day tank was empty, the pumps did not work in the run mode. Kris- KLChurch
- Post #291
- Forum: Generators
-
mep 004a no fault lights working plus more
I firmly believe if we can get VDC to the IP the engine will start. But I don't know how this wiring spaghetti gets there. Also the lift pumps needs to be working in the run mode Kris- KLChurch
- Post #290
- Forum: Generators
-
mep 004a no fault lights working plus more
Tried to start the engine at 20 sec run intervals. 7 times. The starter was getting hot so I quit. This was with the jumped connector and no battle start. Need to recharge the batteries but they were running strong Kris- KLChurch
- Post #289
- Forum: Generators
-
mep 004a no fault lights working plus more
The test to start the engine. Run command no pumps with ab and gh jumped battle command no pumps. Start for 15 sec no engine start but cranked. will try again and again until the batteries are dead again Kris- KLChurch
- Post #288
- Forum: Generators
-
mep 004a no fault lights working plus more
This is what I got testing G&H jumped and A& B jumped and black wire to ground G&H With the stop mode and ground. continuity Run command no 24VDC, didn't test for continuity. Start command 24 VDC Kris- KLChurch
- Post #287
- Forum: Generators