• Steel Soldiers now has a few new forums, read more about it at: New Munitions Forums!

  • Microsoft MSN, Live, Hotmail, Outlook email users may not be receiving emails. We are working to resolve this issue. Please add support@steelsoldiers.com to your trusted contacts.

Search results

  1. G

    Air conditioner install using Waterloo parts

    Here's the FMTV A1 LSAC AC system drawings: Item #3 is the suction hose (low side) from the evaporator to the compressor. This connects to a 90 degree pipe with a support bracket that fits into the back of the compressor. The low side charge fitting is part of the fitting on the back of the...
  2. G

    Any master mechanics of LMTV willing to travel to Puerto Rico?

    Aw man. Totally would and I have all the manuals for every model but can't get away - have my shop to run and have to take care of my elderly mother. Good luck - hit me up if you need manuals and diagrams, etc.
  3. G

    Wiring - M1088A1

    Likely an issue for those that need inspections. Luckily I have no such requirement.
  4. G

    Wiring - M1088A1

    One of the wires for the dash buzzer routinely gets disconnected and taped up because whoever did it doesn't want to listen to the low air warning buzzer. Especially on the civilian side since most of us are keenly aware of the pressure in our air tanks and don't need the idiot buzzer.
  5. G

    Air conditioner install using Waterloo parts

    It really doesn't matter...... it's a lot like an incandescent bulb - you need current flow. Same with the heater - if you want heat you need flow through the core. The direction of flow is pretty much irrelevant. It's just a radiator located inside the cab.
  6. G

    M1083 Voltage drop and intermittent start issues found

    Wow. Such a mess. You can delete the polarity protection device if you don't believe you are silly enough to connect the batteries incorrectly like PVT Snuffy. GD
  7. G

    Air conditioner install using Waterloo parts

    You can use the blower hose adapters from the heater unit so don't worry about that. You will have to bend the tabs a bit and crush them oval to get them in but it does work and in fact I had to do this on the passenger side due to the proximity of the transmission control unit. I looked in...
  8. G

    Air conditioner install using Waterloo parts

    My only concern with that is pests climbing up into the unit. Have you called Red Dot?
  9. G

    Winch install question/issue

    The little one is a 40 lb Shepherd mix (German and Miniature) and she can jump in with no real issue. Sometimes she misses but she always gets it on the second try. She is 2 years old. The big guy is about 75 lbs and he is 1/4 Australian shepherd. He initially tried jumping in but failed too...
  10. G

    Winch install question/issue

    Nothing like a trained dog or pack of them to discourage unwanted aggression. My shepherds (2) ride shotgun in my LMTV and I have no worries about it's safety. The imposing nature of the machine and two unfriendly canines in the cab deter all interest in my experience. The dogs are big babies in...
  11. G

    Air conditioner install using Waterloo parts

    They are similar to what is on the heater unit. They are the flanges that the ducts which direct airflow at the driver and passenger foot wells are attached to. In my post I made a note that you must use the duct ring from the heater unit on the AC unit for the passenger side duct since the...
  12. G

    Air conditioner install using Waterloo parts

    It will be obvious when you pull the heater. The 4 pin connector matches the existing connector to the heater for fan power and panel illumination IIRC. The 2 pin orange and black is power and ground for the stepper motor flapper controls, AC compressor clutch, etc. IIRC the black goes to...
  13. G

    Air conditioner install using Waterloo parts

    Here's my write up on installation thus far with all the parts from Waterloo. Definitely had the 4 drains on mine as well - had to drill out holes with a template. I just made mine from cardboard and that worked fine. I'm waiting on some official hoses and drier from Red Dot to complete the...
  14. G

    M1079 van body on M1078

    Well the GVW of my 1079 is still 5.000lbs higher than it's curb weight. So even with the enclosure bringing the curb weight up to 21.5k vs 17.5k for the 1-78 it is rated for another 5k on top of that. GVW on my 1079 is 25,980
  15. G

    M1079 van body on M1078

    My 2008 M1079A1R has no noticeable "rock and roll" on the road. Not sure what you are experiencing exactly but mine is absolutely stable.
  16. G

    100A -> 200A/400A alternator replacements

    The 260a alternator from Niehoff is about $3400 retail with regulator. You do need a different shock tower and different mounts and of course larger wiring, but I don't think that would amount to $12.5k
  17. G

    Registering an M1078 in Washington State

    Oregon gave me a rash of shit over my truck and I wasted 4 hours at the DMV only to find that my money isn't good enough for the state of OR so I just licensed my truck in Utah with these guys: www.dirtlegal.com Cops don't give me any problem. I live literally across the street from my city...
  18. G

    Manual transmission LMTV?

    Why would you do this? The auto is better in every single respect. 1st gear is your low range, and you have a torque converter so you can crawl at real low speeds. 3126b is not mechanical. It has an ECU similar to the C7. 3116 is the mechanical engine used in the A0 but the transmission...
  19. G

    When It Rains, It Dies

    Before you test for battery amperage draw make sure you pull all the circuit breakers in the M1079 van enclosure on the side of the blackout/emergency light panel. These power the relays that control the lights and they are energized even when the lights are off. There's a warning sticker to...
  20. G

    AWD and Slip

    The ABS system is capable of modulating brake application, and when manufacturers implemented "traction control" it was basically just a software upgrade to the ABS systems. Which is why they did it.... it's not great or even good.... it's mostly a marketing ploy and it was essentially free...
Top
AdBlock Detected

We get it, advertisements are annoying!

Sure, ad-blocking software does a great job at blocking ads, but it also blocks useful features of our website like our supporting vendors. Their ads help keep Steel Soldiers going. Please consider disabling your ad blockers for the site. Thanks!

I've Disabled AdBlock
No Thanks