Search results

...... I kinda want a bobbed deuce..... let me know if you decide to do that. There were no LMTV's in my unit when I served and I was attached to motorpool where I worked on a lot of M35's, HMMWV's and 800/900 series trucks. I'm in Oregon so not far from you. The LMTV is a sweet platform. No...

I edited my post with some pics I found of the destruction. I would still pull the head. You can't assume the condition of the disc valve springs. Could be an easy fix to prevent a very bad hard-down later. Rick

There's a LOT of water, and enough oil to make milkshake...... I'm not (yet) an LMTV expert, but one thing I DO KNOW is compressor and compressed air systems. I spent several years working for Roger's Machinery both assembling compressors from parts for the rental fleet and rebuilding recip...

Could be that PVT Snuffy rotated the housing on the bumper. They are only held on by three 13mm nuts on the back side. Try rotating the housing? Are the incandescent bulbs right way up? I would say if the housing isn't rotated incorrectly then the projectors you got were probably made...

The Silky japanese saws are amazing. I have a couple of them. Great for backpacking, etc. My german shepherd has a Silky PocketBoy in his backpack. He also carries (along with his bowl, food/water, and treats) a small first aid kit, a bite/sting kit, and a pocket knife. Because if someone falls...

Yeah looks like that's a candidate. My only concern is are the mounting straps included? They are included with the original Bendix unit. The original Bendix AD-9 24v part numbers seems to be 65224 (includes mounting bracket and wiring harness)...

Well it looks like that Bendix AD-9 is a reasonable choice and cheap too. The pic above is clearly an A0 truck since there's no battery disconnect. Rick

Honestly looks like a gimmick that tries to do everything and probably does all of it poorly. An axe is a great tool when used carefully (it is a seriously dangerous tool if you don't know what you are doing) - it is WAY out-performed by even a hand saw for most applications. Unless maybe you...

I think his intuition (OCD) is on the right track. Doing a little searching I would tentatively say you have a (much more common) Bendix AD-9 Dryer or a knock off of same (it appears to be a popular design that is copied): https://www.google.com/search?q=bendix+ad-9+air+dryer If that's the...

Ok that does NOT use the cartridge I linked to previously. The one Iinked is for the Haldex unit on my A1R: I would say - based on the lack of matching sand-colored paint that it's been upgraded.

I checked the heater end of the wiring - it's just a single terminal from the solenoid into the heater. And it looks untouched and stock. You are correct - TL508 is the solenoid side of the wire after the fusible link. TL507 connects to the LBCD. I swapped it back and fired it up. No more...

Well - I did confirm that the heater is currently hooked to the wrong terminal. It's on the 12v load terminal, and should be connected to the 24v batt terminal. On my truck and in my schematic it is TL508. I'm going to move it today. Wiring looks all original CAT and the solenoid is labeled...

Ya know I wondered about why it wasn't a 24v heater. :unsure: I have been doing searches on the C7 heater trying to find specs like amperage draw, etc..... Well I know for a fact that I didn't swap them but someone had been in there for sure at some point because I clearly remember at least one...

My mistake they are $165 from NAPA. About the best price I can find is on eBay at the moment: https://rover.ebay.com/rover/0/0/0?mpre=https%3A%2F%2Fwww.ebay.com%2Fp%2F1929660435 Make sure yours looks like this one. The plastic cartridge that is under the big aluminum dome on the top. Rick

Video of the 14v gauge on cold start with the intake heater running. If you set the high idle it draws more power as more air is pulled across the heating element. Voltage goes back to 14v when the grid heater turns off. Having no frame of reference for normality I figured I would get opinions...

There are several different drier designs depending on A0 vs. A1 trucks. It is generally recommended to replace the entire drier with a newer design on the A0 trucks as much better is available now. On my A1R truck I was able to order the drier cartridge from NAPA for like $65 or so. The air...

This is a 1079 A1R truck that came with the 260a stock. The LBCD is rated at 200a on it's data plate so I would assume it disconnects around/above 200a.... But there's nothing that says if that's the 14v or 28v or combined rating. And the LBCD relies on the VR to send it the load signal which I...

So the question is - did these guys leak or did they blow up? Given I have the 260a alternator.... The truck did already have a newer voltage regulator when I got it. Given the state of the connections though I'm not that surprised.

Yeah you can't see them because they are set in the epoxy - but I can test between the batt and load terminals and they are definitely present. There's about a 0.4v drop in forward bias so I'm guessing a Schottky Diode is being used. I don't know the size of them but I would assume they are...

Battery disconnect is the pair in the box on the back of the battery tray that has the manual disconnect on the underside.