Search results

I will check tonight if I can otherwise Friday sometime on the threads. I know the bolts that hold the lower cover on the PDP fit into the ground tap (although too long) but the 12v is a bigger size. I did the mod everyone else is doing installed a 12v outlet into the lower panel using the...

Question radbad... Did you have to remove the front driveshaft at the trans side to get the driver's side filter out? The procedure in the -20 says that is required. My 97 LMTV was about 3 quarts overfull when I got it from GP. Warmed up to operating temps, drove around for about 10 minutes...

There is also a 12v un-fused stud mound (as well as a 24v and ground) on the left side of the Power Distro Panel in addition to the 12v wires already provided. Also, you can run your own battery taps/fuses off of the batteries if you know your way around a multi-meter. The way the batteries are...

I used Rounders Logistics to transport my LMTV on a flatbed and was very pleased and thankful I didn't self recover after getting the truck home and finding all the issues not reported in the GP inspection report. They are a vendor on SS in the Transportation Forum. I was a nay-sayer on paying...

Awesome! Thank you Suprman... I will open up the kit this weekend... I know I have an old Win2k machine and I may have an old laptop with the 9pin serial port but I don't think its XP. I would bet I have an old copy of XP I could install. sweet!

Wasn't quite sure what this test set was when I bid $25 bucks on GL but I wound up with it. The kit looks pretty complete but no TM or CDs... I haven't done much research yet but I am hoping this would have capabilities to use it on the 97 LMTV... Maybe Suprman may know more details? Any help...

Thanks to Lmtv772 sending me a drivers door glass my LMTV now is all sealed up. In addition to the shattered window not reported in the GP inspection report the inside handle would not open the door. After pulling the window components apart I also looked for a lock rod clip that would work with...

Do you have fluther details on which "other FMTVs" ran the 3.07 gears (models/years)? Just wondering without actually checking the axle data plate.

Yes, please share. I got both my haldex brake chamber plugs and cage bolts off @bay just searched LMTV parts but it would be nice to see actual source and part numbers.

Is the stowed position directly under the bags? My pins are missing. I would think the issue off-road is bouncing and jittering all over the place so the little level sensor would be trying to level the cab constantly.

Sandcobra164, no we are talking about the cab air springs and the holes and pins at the bottom of the brackets that the air springs sit in.

Shadowrwolf, I am looking at the -10 on page 2-373 and I see exactly what you are referring to. The weird thing is that this page as well as 2-375 which talks about changing CTIS settings are right in the middle of the 2-58. PREPARATION FOR INTERNAL AIR TRANSPORT (CONT) instructions. Almost like...

I noticed the pin mount holes in the air spring base on mine. The pins are missing with just the wire holders dangling there. Will fire up the TM in the morning and do some reading.

Bob, Yea I was concerned about leaving it on all the time and all the air bleeding out but I guess that is no big deal since you should drain your tanks if going to sit anyway. I was just wondering if you turn off the valve when raising or lowering the cab if there is a potential for damage or...

Ok, thanks all for your feedback. I am assuming that you release the auto level knob when you raise/lower the cab. Thanks! OD

OK. Thanks for the info I guess I will turn it on and leave it there. Do you switch it off when raising/lowering the cab? OD

OK, issue number two on the 97 LMTV... after topping off the fuel tank and firing up the truck the fuel gauge is inaccurate. Does not read full. Sometimes it shows 1/4 tank then when running skips up to 1/2 tank but never reads full. while running every now and then it does a tic-toc from its...

I was wondering if people leave their cab air springs engaged (auto leveling) when they are not operating their trucks or do you release the knob at the manifold control box? Thanks! OD

1997 S&S M1078 8300 miles. Just cleaned up after transport from GP. Went out for the first test drive of the M1078 early yesterday morning. Warmed the truck up to 165, verified CTIS is in Hwy mode with a SOLID red light and tire pressures are at 55psi. Around 25-30 mph the CTIS Ovspd warning...

I updated my posting to indicate the privacy warning for some devices before the link. It works ok on my desktop where I did the search and found it. Checked my phone and it gives me the same warning you received. Looks like its certificate is not up to date. I had an option to bypass and go to...