Search results

Let me know what you can do and when.

does anyone know what seal and bearing numbers are used for the v100 transfer case. mine is leaking on the front output shaft and i think one of the bearings is on its last leg as i have a very loud whine from it. the fuild is at or slighrly above the full level with some lucas added to see...

Been running a Holley 670 CFM truck avenger the last few years on the V100 and it started running a bit rough, etc, had some serious corrosion in the fuel bowls etc, working with holley on this. In the mean time, I did some research on CFM, Carbs, etc and did some calculations based on stock...

I just finished painting a extra set of V100 rims and have modern 5 ton 14.00x20s mounted on them which I'll be switching out with the Mohawks i'm currently running on it. The Mohawk's have a date of 1974 if I remember correctly and look just like the commandos. For shows or other "special...

Need for static display.

i know its been quite a while since the last post on tbis topic but does anyone know what happened to these two m56s

Looking for the following cupola and any or all pieces for it too.

Looking for a good X200-3 cross driver transmission. Similar to the X200-4 and 4a that is used in late M113A2 and M113A3 APCS. Let me know what you have or if you know of one..Would look very similar to the ones shown below.

Welcome from Brookhaven. Glad to have you.

I really thought that everyone knew what a Johnson Rod is... :-)

and sell out combat fighting vehicle owners, like the NRA did to MG owners in 85/86?

Looking for the following manuals, hard or soft (electronic/pdf) would be fine. TM 9-2530-201-35 TRACK AND SUSPENSION TM 9-2520-225-35 ELEVATION & TRAVERSE SYSTEM TM 9-2520-225-35P ELEVATION & TRAVERSE SYSTEM TM 9-1290-269-50 T219 SCOPE MOUNT TM 9-1240-243-34 T186 TELESCOPE TM...

it's a bad design in my opinion, the fuel cap sits below were the water level would be and the vent allows water to enter. I dump some rubbing alcohol in mine from time to time to absorb the water, I have a water seperator in the fule line as well. It's in place of the standard military fuel...

does anyone have information on a M37 Seal I have 5330-141-2461, I believe it's for the transfer case. Also these parts were with the seals above, but not sure what they go to.... Universal Joint Kit 2520-737-2674 Seal 5330-737-5410 Seal 5330-291-7947 Seal 5330-286-7058 Thanks Jason

Is it heavy? Pain in the ass to move around the shop if it's not running? if so, then you're in the right place.

It's an original M416B1 (serial number 5XX) with a delivery date of 9-65. Might leave these tires on as I sorta like them. Need to fix a few oil leaks first.

Would be happy to, as stated previously, I'm going to pick up tomorrow. Regarding the regulator, will more than likely swap it out for the correct mechanical one. I have a pile of nice ones from years of collecting crap. The hose from the intake to the air cleaner looks like a radiator...

Sorry, was in a hurry to get to a meeting... here you go. Also, needs 6.00x16s as it has 700s on it right now.

Just picked bought this beauty, going to pick her up tomorrow. Runs and drives, only thing it really needs are the following: 1) Correct Seat Cushions and Covers 2) Tool box to replace the 50 cal ammo can that replaced the tool box behind the driver's seat. 3) Correct top bows, currently has...

I have an XM800T with a 6V53T engine that has been sitting since the late 1970s and more than likely has not been started since then. I have not pulled the engine out of the vehicle yet, but plan to sometime in the next few weeks. The engine has about 310 hours on it (according to the meter on...