Search results

It sound like we have around 5. I had mentioned to the parade coordinator that we might have about 6 and she indicated that 6 would be fine. The #20-23 block was just a continuous group of unissued numbers near the front. I've sent a note asking if there is a limit we should stick to, will...

Hi all, Crusher has a conflict this year so I am coordinating our participation. Of the parades we have done this one is my favorite. It goes through a residential neighborhood and the crowd really appreciates the MVs. If you search Edgewood here on SS you can see the prior threads with...

Sorry, I meant to post the image of the range diagrams.

The M977 and M985 range diagrams are together in the TM. The question I have is, what can you expect to lift on to the bed of a M977 with the crane at the 9 ft/4500# position? Is the geometry such that you can lift a typical 3500-4000 pound car/jeep? Maybe a lightened HMMWV? :drool:

Charles, do you have DDEC III/IV? Have you tried to read fault codes? Do you have TM-9-2320-360-20-3? You can get it on the internet, e.g. at liberatedmanuals.com. FWIW, in the section for "Can't get full power", the second thing listed after "Plugged Fuel Filters" is "Hose not connected to...

So how does a "normal" amount of knocking coconut sound correspond to load? My 1984 M925 has more "coconut" effect than my 1986 M925A1, and it increases with load. It is not really present at all when coasting. I had a career army truck mechanic ride in it and he said it is completely normal...

5tonbrian, see the diagram in post #21 (top of page 3). If you have gages then there is power on wire 5. Beside the PCB, other problems could be the starter switch on the dash or the Neutral Safety switch. Can you probe wire 499 (Term E) at the PCB and see if you are getting 24V there when...

M916a1 with DD has a Series 60, an inline 6.

If you are not getting gauges on, then it sounds like PCB or the Battery switch or related connection. This seems to come up about once a week...maybe it should be a sticky. http://www.steelsoldiers.com/showthread.php?113634-Ever-see-inside-the-Protective-Control-Box Chris

They are toward the end of TM Volume 4 (TM 9-2320-272-24-4).

Search "inside the protective control box"

The P2P program shows the air horn supply coming from the pressure protection valve, should be common with the supply to the wipers...

From the P2P program...the air horn supply comes from the pressure protection valve, should be common with the supply to the wipers...

Reminds me of when I was young and broke. I fixed a number of radiators by crimping and soldering, even breaking out heavily damaged sections of the channels and folding over and soldering. The key is to get it clean enough and use flux to get the solder to flow out. I went looking for a...

Here are a couple of pictures. Thanks Guns for bringing the M927. Great time in spite of the rain.

I received the map of the parade route and instructions, attached. We are to arrive at 6:00 pm, stage behind the Kroger store. So far Guns with 1-2 trucks, and I will have the M925. Any more?

Is anybody coming through NM on I-10 and could bring a tire from Las Cruces (40 miles west of El Paso) to Louisville? Thanks, Chris

I talked with the parade coordinator today. She would like to have the MVs up front, and have us arrive by 6:00 pm. If you let me know you will be later, I will save you a spot in line. I put 2-4 trucks on the registration form and submitted it. More trucks are fine, just post that you are...

I wonder how a M939 would run with a big block Chevy in it?

There was some discussion added on to the thread for last year's parade regarding this year's parade, but no commitments were made for this year and the thread went quiet. I am starting a new thread so the date in the title is correct for 2014. The 2014 parade is Friday June 27 at 7 pm, from...