Search results

On the fuel filter, there should be a small o-ring (Dash-202 size?) on the screw stem or it can leak fuel or air. You want one in place. If your existing one is hard / dry / cracked, I would replace it. All the best, 2Pbfeet

FWIW: I use a small panel mount digital frequency meter that I wired to a short extension cord, and put a heat shrink cover on the terminals to keep an eye on my generators. It is bright, easy to read, and portable. If I'm not at the generator when it is in use, I plug it in near me in the...

I am sorry, but I can't help you the connector. I'm the wrong guy for 535 details. I just was interested in your questions and did some poking around. I've been known to walk the aisle in auto parts stores looking for matching connectors, but I'm sure that other folks here can do better than...

Hmmm...@coachgeo I don't know what to say. The link worked for me. Here is the file;

I've driven by Ft. Lewis. Pretty area! I've driven by many of the locations in the video, actually. I enjoy seeing the history. All the best, 2Pbfeet

If you want to see these sort of saws (not on a generator) look like from WWII, DeWalt has an old promotional video; I caneasily imagine SeaBees setting up a similar, though perhaps smaller operation with it. All the best, 2Pbfeet

Did you try a search for "RV hookup panel"? It seemed to come up with a few for me... https://www.amazon.com/Temporary-Power-Outlet-Panel-Weatherproof/dp/B0C9QM5TJ8/

@Chainbreaker A 16" radial arm saw is going to need a pretty substantial motor. I have seen a number of that size and vintage radial arm saws with five and ten HP motors on them, always three phase. That is scary powerful in my book...

If you go the break in oil route, change the oil and oil filter again at 100 hours. I have done it on a few engines that I either didn't know the history of, or had doubts about the cleanliness (dirt / casting sand, etc.) of the engine. I agree with @Ray70 that you can't have too much ZDOP added...

If you need more wire, I believe that the type of wire that you are looking for "TGGT", aka Teflon-Glass-Glass-Teflon covered nickel coated copper wire. While perhaps not stocked in a basic box store, it is sold by a number of cable vendors, eBay, Amazon, and others. Just know the gauge wire...

".ru" ...

There is an older thread that suggests that pump; https://www.steelsoldiers.com/threads/802-803-fuel-pump-fittings.184917/post-2477378 My recollection is that @DieselAddict here talked to Airtex/Carter and got the skinny on the replacement...

Congratulations on your fix, and getting it running! If it were me, I would think about a small overcoat of conformable sealant to help protect the longevity of your board and repair. There a number available, but I don't know what your board might benefit from. (I don't know what is on there...

I think the fuse was/is a (Mersen) Ferraz Shawmut "Amp-trap" ATX-3, where the X is missing, perhaps "M" for midget (1 1/2" long)? There are eBay listings for Ferrari ATM-3 listings, if you want to look it up. e.g. https://www.ebay.com/itm/383671751698? That would have been a fast acting fuse...

They (Craig labs) do make several different concentrations, so I think that the old brain isn't so feeble. The D5 is 5%, though they also make several 100% versions (different applicators). https://caig.com/deoxit-d-series/ The D5 should do what you need, squirt it in, and with the power off...

White smoke in a diesel is generally cold fuel, i.e. not fully combusted. Often the cause is a bad injector that is overfueling a cylinder, but a cold engine can do it for a while, and I have it happen with bad rings. Overfueling in general, due to an air leak in the fuel line, or a bad...

Where else do you recommend? I did the intakes, the drain under the engine, and sealed the power feed through. The coolant drain I protected with a female brass GHT to barb adapter, with the female section flipped over to protect the hose. Anywhere else of concern? Can mice get in through the...

The third possibility is that you buy a variable frequency drive for the pump so that it soft starts. If you go that route, I would recommend filters in and out of the VFD if your well pump is a submersible pump down the well. If it is on the surface, I would put them at least on the generator...

@Guyfang Thanks! I find it interesting to see the schematic of the design of the controller. All the best, 2Pbfeet

The manual scan isn't very high resolution, so I don't think it is exactly readable. General idea, yes.