Search results

I used a seat I got at tractor supply good contour very comfortable and bolted right up. Now I need to remove passenger side and replace with driver spring base so I can do the same on the other side. I will then have room in the center for the red dot AC and the Combat Crock Pot. Sorry about...

Ok I got lucky A=22-28 volt+ B=Ground C=not Connected or N/C

So all this has convinced me that I need one for my truck which I have just purchased. I also need a cord. I found the connector but like others I need a pin assignment so I can wire the plug properly. I am still trying to find manuals or blueprints or something that will explain the pin...

I have jumped my deuce several times with a 12 volt system and never unhook a single wire. Hook positive to the positive and the hook the negative to the frame or other metal area not to the battery. Start the truck if you have enough amps to turn it. Never hurt the 12 volt vehicle the first...

So far I have installed all hardware and mounting brackets for the new winch. I have installed all the linkage and operation lever and tomorrow I will install the PTO. I am in the process of rebuilding the winch putting in new seals and such. Once I finish I will install the winch and drive...

I had the same problem. There is a large hole where the steering column goes through the fire wall. It was letting in a large amount of heat from the engine compartment. while driving I filled it with spray on expandable foam no more heat from the engine into the cab.

Congrats Welcome from Pleasanton Texas.

Ok just to let everyone know got my new air pack and installed it today all is well. I want to thank everyone for all there help and suggestions. You guys are the greatest thanks again.

Ok just wanted to let everyone know its fixed. It was the flasher but I went ahead and replaced the turn signal switch, and the light switch. So I have spares of those now. Thank everyone for all there help all is well.

Yes I am reviewing the TM's and learning about what wires go where and I planned on testing them first. But Upon tracing and visual inspection all looks in good order. I hope I will feel informed enough to get my meter and start testing tomorrow and should receive new parts either Thursday or...

I am not real bright. I always order all the parts to replace the entire system start to finish. Then I replace parts one at a time until I find the problem. I then replace the parts I used and store the rest for future problems. I am getting quite a stock pile of parts. HAHAHAHAHAHA

Yes I should have specified I changed all the soft brake lines. (Rubber)

In reply to the earlier post. I have replaced the radiator and flushed the system. replaced all the fluids. Replaced all belts and hoses basically I have replaced all rubber in the truck including all cab and window seals. The water pump and compressor are in good working order no leaks no loose...

Well I have checked and cleaned the grounds. Replaced 3 bad bulbs. (All Blackout Bulbs) Still no turn signals or flashers so it must be the flasher unit or the turn signal lever. I have ordered both should be here in a few days. Wish a lot of the people I order parts from had express shipping...

Well when it rains it pours I guess. I have had a brake problem over the weekend which I have figured out the problem (Air Pack). Then I had an issue figuring out how to replaces the axle seals (thanks for the help). Now this morning without warning or symptoms of any kind my turn signals wont...

Okay just wanted to thank everyone for there help with this issue. Replacing the wheel cylinders and brake lines did not help the brake issue. I ended up unscrewing the J-pipe enough so it would constantly release air while brake applied and still maintain air pressure. This allowed the brakes...

Thank You I will remember that. I did all that work got all the way to the seal and thought it was going to be like normal seal just pop it out pop the new one in. But the seal housing looked like part of the differential. The truck was on the side of the road but it was close to home so no...

Ok that was a big help thank you. o\Old seals out new seal in ready to reassemble front hub. THANK YOU for the Help

Ok so while trying to figure out my brake problem I decided to replace all the parts in the front hub since I have it apart wheel cylinder, brakes, bearings, races, and such. I disassembled the front hubs and found a lot of gear oil in the steering knuckle so I disassembled some more to get to...

I have had the hubs and wheels off the bearings are good it is definitely the brakes. I think the air pack is building pressure or not releasing pressure. When I push on my brake pedal I have very little free travel pedal moves a few inches and truck will stop on a dime. When I release I can...